")+"
<%+%*M&"+M&!<%+.+M".,MB[\#+$&%
Ldg`e^ZXZ
;ZcXZ
Blade
Figure 86.
HZXdcYXjiidXgZViZVgVWWZi#
6.
GZXdccZXii]ZhVlidi]ZedlZghdjgXZ!i]Zc
eZg[dgbi]ZXji#
7.
AVni]Zldg`e^ZXZ[aVidci]ZiVWaZ!Vhh]dlc
^c
Figure 86
!VY_jhii]ZhVlWaVYZ]Z^\]iid
^ciZghZXi l^i] i]Z [^ghi Xji! i]Zc eZg[dgb i]Z
hZXdcYXjiidXdbeaZiZi]ZgVWWZi#
;ZcXZ
Blade
Ldg`e^ZXZ
Figure 85.
GVWWZiXjii^c\l^i]VhiVcYVgYWaVYZ#
6g^ee^c\WaVYZ^hine^XVaani]ZWZhiWaVYZidjhZ
[dg Xjii^c\ gVWWZih l]Zc jh^c\ V hiVcYVgY WaVYZ
WZXVjhZ^igZbdkZhhVlYjhikZgnZ[[^X^Zcian#HZZ
Page 33
[dgWaVYZYZiV^ah#6ahd!VhVXg^[^X^Va[ZcXZ
^hcdigZfj^gZYl]ZcXjii^c\gVWWZihl^i]VhiVc"
YVgYWaVYZ#
To cut rabbets with the standard blade:
1.
9>H8DCC:8IH6L;GDBEDL:G
2.
:chjgZ i]Vi i]Z g^k^c\ `c^[Z VcY hiVcYVgY
iVWaZ^chZgiVgZ^chiVaaZY#
3.
BVg`i]Zl^Yi]d[i]ZgVWWZiXjidci]ZZY\Z
d[i]Zldg`e^ZXZ!hdndjXVcXaZVgan^YZci^[n
i]Z^ciZcYZYXjil]^aZ^i^haVn^c\[aVidci]Z
hVliVWaZ#
4.
GV^hZi]ZWaVYZjeidi]ZYZh^gZYYZei]d[Xji
YZei]d[gVWWZiX]VccZaYZh^gZY#
5.
HiVcY i]Z ldg`e^ZXZ dc ZY\Z! Vh h]dlc ^c
Figure 85,
i]ZcVY_jhii]Z[ZcXZhdi]ZWaVYZ
^hVa^\cZYl^i]i]Z^ch^YZd[ndjggVWWZiX]Vc"
cZa#
Cutting Rabbets with a Standard
Blade
·>[i]Zldg`e^ZXZ^hkZgniVaa!
dg^hjchiVWaZ
l]ZceaVXZYV\V^chii]Z[ZcXZ!aVn^i[aVidc
i]ZiVWaZVcYjhZVYVYdWaVYZideZg[dgb
i]ZgVWWZiXji#
DO NOT place a tall board on edge to per-
form a rabbet cut with a standard blade.
Workpieces that are too tall to properly sup-
port with the fence can easily shift during
operation and cause kickback. Instead, place
the stock flat on the saw and perform the
rabbet cut with a dado blade, as instructed
on Page 45.
15
30
45
