"&)"
BdYZa<%+.(B[\#&&$%-VcYAViZg
Vise Fence
;dg dei^bVa Xjii^c\ gZhjaih! i]Z XZciZga^cZ d[ i]Z
WaVYZ bjhi WZ Y^gZXian dkZg i]Z XZciZga^cZ d[
i]Z ldg`e^ZXZ [dg dei^bVa Xjii^c\ gZhjaih# I]Z
ldg`e^ZXZ Va^\cbZci ^h YZiZgb^cZY Wn i]Z edh^"
i^dcd[i]Zk^hZ[ZcXZ#I]ZVc\aZd[i]Zk^hZ[ZcXZ
YZiZgb^cZhi]ZVc\aZd[i]ZXji#H^cXZi]Zedh^i^dc
VcYi]ZVc\aZd[i]Z[ZcXZVgZgZaViZY!Wdi]bjhi
WZVY_jhiZYVii]ZhVbZi^bZ#
To set the vise fence position:
1.
9>H8DCC:8IH6L;GDBEDL:G
2.
GZbdkZ i]Z k^hZ Vc\aZ XVe hXgZl VcY i]Z
k^hZbdjci^c\XVehXgZl
Figure 9
#
4.
L]^aZbV^ciV^c^c\i]ZVc\aZd[i]Zk^hZ[ZcXZ!
ha^YZi]Z[ZcXZVadc\i]ZWVhZjci^ai]ZXZc"
iZga^cZ d[ i]Z ldg`e^ZXZ ^h Y^gZXian dkZg i]Z
XZciZga^cZd[i]ZhVl
Figure 11
#
Note:
Because the centerline of the saw
changes as the saw arm moves, it is neces-
sary to lower the saw for proper alignment.
Check for proper alignment periodically as
you adjust the fence position.
K^XZ;ZcXZ
7aVYZ
Ldg`e^ZXZ
BVX]^cZ7VhZ
Figure 11.
Blade/workpiece alignment.
5.
Ha^YZ i]Z [ZcXZ id i]Z cZVgZhi bdjci^c\
]daZh! i]Zc ^chZgi Wdi] XVe hXgZlh# 9djWaZ
X]ZX` i]Vi i]Z k^hZ [ZcXZ ^h hi^aa hZi [dg i]Z
YZh^gZY Vc\aZ d[ Xji! i]Zc i^\]iZc Wdi] XVe
hXgZlh#
Figure 9.
Vise fence.
K^hZ6c\aZ
8VeHXgZl
K^hZBdjci^c\
8VeHXgZl
3.
EaVXZ i]Z ldg`e^ZXZ V\V^chi i]Z k^hZ [ZcXZ!
i]Zc jh^c\ i]Z hXVaZ Vh V \j^YZ! hZi i]Z
Veegdm^bViZYZh^gZYVc\aZd[Xji#
Note:
If you are making 45° cuts, remove the
vise angle cap screw and reposition it to the
location shown in
Figure 10
. This will prevent
any unwanted movement of the vise fence
during tightening of the vise.
Figure 10.
Cap screw positioned for 45° cuts.
K^hZ6c\aZ
8VeHXgZl
