Model G0812 (Mfd. Since 2/16)
-21-
10. Check function of cutting fluid pump
by turning cutting fluid pump switch
(
STAND BY
START
<< I
OFF
1
2
3
4
5
6
7
8
9
0
HIGH
LOW
A
E
M
H
B
C
F
I
J
K
L
G
D
STOP
, D) all the way to the right.
11. Verify that cutting fluid flows through nozzles
into blade guides, then turn switch
OFF.
12. Press raise headstock button (
B
A
C
D
E
F
G
H
I
J
K
L
, E) and
raise headstock several inches, then press
vise close (
STAND BY
START
<< I
OFF
1
2
3
4
5
6
7
8
9
0
HIGH
LOW
A
E
M
H
B
C
F
I
J
K
L
G
D
STOP
, J) button.
Note: As a safety precaution, saw motor will
not start unless vise close button is pressed
first.
13. Start blade movement by pressing blade start
button (
B
A
C
D
E
F
G
H
I
J
K
L
, I) while keeping your finger near
Emergency Stop button (
A
D
G
H
I
J
K
E
F
C
B
, C). The machine
should run smoothly and without unusual
problems or noises.
14. Press Emergency Stop button (
A
D
G
H
I
J
K
E
F
C
B
, C) in com-
pletely to stop machine.
15. WITHOUT resetting Emergency Stop button,
press hydraulic motor button (
B
A
C
D
E
F
G
H
I
J
K
L
, G), vise
close button (
STAND BY
START
<< I
OFF
1
2
3
4
5
6
7
8
9
0
HIGH
LOW
A
E
M
H
B
C
F
I
J
K
L
G
D
STOP
, J), then blade start button
(
B
A
C
D
E
F
G
H
I
J
K
L
, I). The machine should not start.
— If machine does not start, Emergency Stop
button safety feature is working correctly.
Congratulations! Test Run is complete.
— If machine does start (with Emergency
Stop button pushed in), immediately dis-
connect power. Emergency Stop button
is NOT working properly and must be
replaced before further using machine.
16. Reset Emergency Stop button, repeat Steps
12–13, then press Stop button (
B
A
C
D
E
F
G
H
I
J
K
L
, H) to stop
machine.
17. WITHOUT pressing Stop button again, press
hydraulic motor button (
B
A
C
D
E
F
G
H
I
J
K
L
, G), vise close
button (
STAND BY
START
<< I
OFF
1
2
3
4
5
6
7
8
9
0
HIGH
LOW
A
E
M
H
B
C
F
I
J
K
L
G
D
STOP
, J), then blade start button
(
B
A
C
D
E
F
G
H
I
J
K
L
, I). The machine should not start.
19. While staying safely away from blade, press
Stop button again, press hydraulic motor but-
ton, vise close button, then start button.
—
If blade does not start, blade cover safety
switch feature is working correctly.
— If blade does start (with blade cover open),
immediately turn machine
OFF and dis-
connect power. Blade cover safety switch
safety feature is not working correctly.
This safety feature must work properly
before proceeding with regular operations.
Call Tech Support for help.
20. Press Emergency Stop button (
A
D
G
H
I
J
K
E
F
C
B
, C) in com-
pletely, then close wheel cover and secure.
21. Reset Emergency Stop button.
22. Raise headstock up all the way, then start
blade. When headstock reaches bottom of
travel, the blade should shut off and the
headstock should move back to the top of its
travel.
— If blade does shut off and headstock
moves back to top of its travel, upper limit
switch is working correctly.
— If blade does not stop or headstock does
not move back to top of its travel, upper
limit switch is not working correctly. This
safety feature must work properly before
proceeding with regular operations. Refer
to
Page 57 to adjust this limit switch.
23. Press Emergency Stop button. Test Run is
complete.
Figure 21. Wheel cover locked in "up" position.
18. Open blade cover and lock in position (see
Figure 21). This activates blade cover safety
switch to prevent saw starting.
Summary of Contents for G0812
Page 84: ......
