background image

-50-

Model G4000 (Mfg. Since 8/09)

SECTiON 7: SERviCE

Troubleshooting

Motor & Electrical

symptom

possible Cause

possible solution

Machine does not 
start or a breaker 
trips.

1.  power supply switched oFF or at fault.
2.  plug/receptacle at fault/wired wrong.
3.  Motor connection wired wrong.
4.  Wall circuit breaker tripped.
5.  Wiring open/has high resistance.
6.  spindle switch at fault.
7.  start capacitor at fault.
8.  Centrifugal switch at fault.
9.  Motor at fault.

1.  Ensure power supply is on/has correct voltage.
2.  test for good contacts; correct the wiring.
3.  Correct motor wiring connections (

page 55).

4.  Ensure circuit size is correct/replace weak breaker.
5.  Check/fix broken, disconnected, or corroded wires. 
6.  replace switch.
7.  test/replace if faulty.
8.  Adjust/replace centrifugal switch.
9.  test/repair/replace.

Machine stalls or is 
underpowered.

1.  Feed rate/cutting speed too fast.
2.  Wrong workpiece material.
3.  Belt(s) slipping.
4.  Motor wired incorrectly.
5.  plug/receptacle at fault.
6.  pulley slipping on shaft.
7.  Motor bearings at fault.
8.  Machine undersized for task.

9.  Motor overheated.
10. spindle rotation switch at fault.
11. run capacitor at fault.
12. Motor at fault.
13. Centrifugal switch at fault.

1.  decrease feed rate/cutting speed.
2.  use correct type/size of metal.
3.  tension/replace belt(s); ensure pulleys are aligned.
4.  Wire motor correctly (

page 55).

5.  test for good contacts/correct wiring.
6.  replace loose pulley/shaft.
7.  test/repair/replace.
8.  use sharp tools at correct angle; reduce feed rate/

depth of cut; use cutting fluid if possible.

9.  Clean motor, let cool, and reduce workload.
10. test/replace switch.
11. test/repair/replace.
12. test/repair/replace.
13. Adjust/replace centrifugal switch if available.

Machine has 
vibration or noisy 
operation.

1.  Workpiece  not  held  firmly  in  chuck/

faceplate.

2.  Motor or component loose.

3.  spindle belt worn or loose.
4.  pulley loose.
5.  incorrectly mounted to workbench.
6.  Motor fan rubbing on fan cover.
7.  Bit chattering.

8.  Workpiece or chuck at fault.

9.  Motor bearings at fault.
10. Centrifugal switch.
11. Quick change gears at fault.

1.  Correctly secure workpiece in chuck/faceplate.

2.  inspect/replace  damaged  bolts/nuts,  and  re-tighten 

with thread locking fluid.

3.  inspect/replace belts.
4.  realign/replace shaft, pulley, set screw, and key.
5.  Adjust feet, shim, or tighten mounting hardware.
6.  Fix/replace fan cover; replace loose/damaged fan.
7.  replace/sharpen  bit;  index  bit  to  workpiece;  use 

correct feed rate and spindle speed.

8.  Center  workpiece  in  chuck  or  face  plate;  replace 

defective chuck.

9.  test by rotating shaft, replace if grinding.
10. replace switch.
11. replace bad gear(s)/bearing(s).

Review the troubleshooting and procedures in this section if a problem develops with your machine. If you 
need replacement parts or additional help with a procedure, call our Technical Support at (570) 546-9663. 

Note: Please gather the serial number and manufacture date of your machine before calling.

Summary of Contents for G4000













































































Reviews: