"''"
BdYZa<.,(%$<.,(&B[\#H^cXZ.$%%
Assembly
I]ZaVi]Z^hh]^eeZY[gdbi]Z[VXidgnegZ"VhhZb"
WaZYZmXZei[dgi]Zild]VcYl]ZZa]VcYaZh#JhZ
V &%bb lgZcX] id ViiVX] i]ZhZ ]VcYaZh id i]Z
XVgg^V\Z VcY Xgdhh ha^YZ ]VcYl]ZZah! Vh h]dlc
^c
Figure 18
#
Lubricating Lathe
GEARBOXES MUST
BE FILLED WITH OIL!
LATHE MAY NOT
HAVE OIL INCLUDED!
Refer to the Lubrication
Section in this Manual
for Recommended
Oil Type.
I]Z]ZVYhidX`!fj^X`X]Vc\Z\ZVgWdm!VcYVegdc
gZhZgkd^ghbjhi]VkZi]ZegdeZgVbdjcid[d^a^c
i]ZbWZ[dgZi]ZaVi]ZXVcWZdeZgViZY[dgi]Z[^ghi
i^bZ#
Gjcc^c\ i]Z aVi]Z l^i]dji d^a ^c V \ZVgWdm XdjaY
gZhjai^cYVbV\Zidi]ZWZVg^c\hVcY\ZVgh·hjX]
YVbV\Z^hcdiXdkZgZYjcYZglVggVcin#
GZ[Zgid
Lubrication
!WZ\^cc^c\dc
Page 64
![dg
YZiV^aZY ^chigjXi^dch dc ]dl id X]ZX` VcY VYY
d^a#
>cVYY^i^dcidi]Z\ZVgWdmZh!lZVahdgZXdbbZcY
i]VindjajWg^XViZVaadi]Zged^cihdci]ZbVX]^cZ
Vii]^hi^bZ#
Note:
If your lathe was shipped with oil in the
reservoirs, do not change that oil until after the
break-in procedure.
Adding Cutting &
Brake Fluids
IdhjXXZhh[jaanXdbeaZiZi]Z
Test Run
^ci]Z[da"
adl^c\ eV\Zh! i]Z Xjii^c\ VcY WgV`Z [aj^Y aZkZah
bjhiWZX]ZX`ZY!VcY^[cZXZhhVgn![aj^YbjhiWZ
VYYZYidZVX]hnhiZb#
6YY i]Z Xjii^c\ [aj^Y d[ ndjg X]d^XZ cdl# ;dg
YZiV^aZY ^chigjXi^dch dc l]ZgZ i]Z Xjii^c\ [aj^Y
gZhZgkd^g^hadXViZYVcY]dlidVYY[aj^Y!gZ[Zgid
Cutting Fluid System
dc
Page 69
#
8]ZX` i]Z WgV`Z [aj^Y aZkZa VcY VYY VYY^i^dcVa
[aj^Y^[cZXZhhVgn!Vh^chigjXiZY^c
Brake Fluid
dc
Page 71
#
Figure 18.
8Vgg^V\ZVcYXgdhhha^YZ]VcYl]ZZa
]VcYaZh^chiVaaZY#
=VcYaZh
>chiVaaZY
