"'+"
BdYZa<.,(%$<.,(&B[\#H^cXZ.$%%
Spindle Break-In
7Z[dgZhjW_ZXi^c\i]ZaVi]Zid[jaaadVYh!ndjbjhi
WgZV`^i^c#I]^hegdXZYjgZl^aa[jaanhZVii]ZWZVg"
^c\h!Vaadli]Z\ZVgiZZi]id[^cYi]Z^gcdgbValZVg
eViiZgc!VcYZcVWaZi]ZajWg^XVciidWZldg`ZY^cid
i]ZgZfj^gZYVgZVh#
To perform the spindle break-in:
1.
HjXXZhh[jaan XdbeaZiZ i]Z
Test Run
egdXZ"
YjgZWZ\^cc^c\dc
Page 23
#
2.
Id ZchjgZ i]Z XVgg^V\Z XdbedcZcih Yd cdi
jcZmeZXiZYanbdkZl]Zci]ZaVi]Z^hhiVgiZY!
gdiViZ i]Z ]ZVYhidX` [ZZY Y^gZXi^dc `cdW hd
i]Vii]ZVggdled^cihidb^YYaZcZjigVaedh^"
i^dchZZ
Figure 23
#
Figure 23.
=ZVYhidX`Xdcigdah#
He^cYaZHeZZY
GVc\ZAZkZg
He^cYaZ
HeZZY@cdW
;ZZY
9^gZXi^dc
@cdW
3.
BdkZi]Zhe^cYaZheZZYgVc\ZaZkZgidi]Zadl
g^\]iedh^i^dc!VcYgdiViZi]Zhe^cYaZheZZY
`cdW hd i]Vi i]Z Vggdl ed^cih id i]Z he^cYaZ
heZZYd[&%*GEBgZ[Zgid
Setting Spindle
Speed
dc
Page 51
[dgVYY^i^dcYZiV^ah#
NOTICE
Do not leave the lathe unattended during
the Spindle Break-In procedure. If your
attention is needed elsewhere during this
procedure, stop the lathe and restart the
procedure from the beginning at a later
time when you can devote your full time and
attention to it.
4.
IV`ZVaahV[ZinegZXVji^dch!gjci]ZaVi]Z[dg
&%b^cjiZh!i]Zcijgci]ZaVi]Z
OFF
VcYlV^i
jci^ai]Zhe^cYaZ^hXdbeaZiZanhideeZY#
5.
GZeZVi
Step 4
[dg i]Z gZbV^c^c\ , he^cYaZ
heZZYh#
6.
HZii]Zhe^cYaZheZZYid'+%GEBVcYaZii]Z
aVi]Zgjc[dgV[^cVa&*b^cjiZhidVaadl^iid
XddaYdlc!i]Zcijgci]ZaVi]Z
OFF
#
Recommended
Adjustments
I]Z[daadl^c\VY_jhibZcih]VkZWZZcbVYZVii]Z
[VXidgn#=dlZkZg!WZXVjhZd[i]ZbVcnkVg^VWaZh
^ckdakZY l^i] h]^ee^c\! lZ gZXdbbZcY i]Vi ndj
ViaZVhikZg^[ni]Z[daadl^c\VY_jhibZcihidZchjgZ
i]ZWZhiedhh^WaZgZhjaih[gdbi]ZaVi]Z#
Factory adjustments that should be verified:
s
IV^ahidX`Va^\cbZcigZ[Zgid
Page 44
8dbedjcYVcYXgdhhha^YZWVX`aVh]gZ[Zgid
Page 80
<^WVY_jhibZcihgZ[Zgid
Page 78
#
Change the oil in the headstock, quick
change gearbox, and apron reservoirs as
instructed in
Lubrication
beginning on
Page 64
. This will flush away any metal
particles that may have accumulated from
the manufacturing process or the spindle
break-in.
7.
8]ZX` VcY! ^[ cZXZhhVgn! gZ"iZch^dc i]Z
K"WZaih Vh ^chigjXiZY ^c
V-Belt Service
dc
Page 83
#
I]Z he^cYaZ WgZV`"^c ^h XdbeaZiZ# 8dci^cjZ l^i]
i]Z [daadl^c\
Recommend Adjustments
hZX"
i^dc#
