background image

H3119 Electric 

3

16

" Crown Stapler

-2

-

9.

USE PROPER EXTENSION CORD

for the tool. Make sure your exten-
sion cord is in good condition.
Conductor size should be in accor-
dance with the chart below. The
amperage rating should be listed on
the motor or tool nameplate. An
undersized cord will cause a drop in
line voltage resulting in loss of power
and overheating. Your extension
cord must also contain a ground wire
and plug pin. Always repair or
replace extension cords if they
become damaged. 

Minimum Gauge for Extension Cords

10. WEAR PROPER APPAREL.

Do not

wear loose clothing, gloves, neck-
ties, rings, bracelets, or other jewel-
ry which may get caught in moving
parts. Non-slip footwear is recom-
mended. Wear protective hair cover-
ing to contain long hair.

11. ALWAYS USE SAFETY GLASSES.

Also use face or dust mask if cutting
operation is dusty. Everyday eye-
glasses only have impact resistant
lenses, they are NOT safety glass-
es.

12. SECURE WORK.

Use clamps or a

vise to hold work when practical. It’s
safer than using your hand and frees
both hands to operate tool.

13. DON’T OVERREACH.

Keep proper

footing and balance at all times.

Safety Instructions For Power Tools

14. MAINTAIN TOOLS WITH CARE.

Keep tools sharp and clean for
best and safest performance.
Follow instructions for lubricating
and changing accessories.

15. DISCONNECT TOOLS

before ser-

vicing and changing accessories,
such as blades, bits, cutters, and
the like.

16. REDUCE THE RISK OF UNIN-

TENTIONAL STARTING.

Make

sure switch is in off position before
plugging in.

17. USE RECOMMENDED ACCES-

SORIES.

Consult the owner’s

manual for recommended acces-
sories. The use of improper acces-
sories may cause risk of injury.

18. CHECK DAMAGED PARTS.

Before further use of the tool, a
guard or other part that is dam-
aged should be carefully checked
to determine that it will operate
properly and perform its intended
function. Check for alignment of
moving parts, binding of moving
parts, breakage of parts, mount-
ing, and any other conditions that
may affect its operation. A guard or
other part that is damaged should
be properly repaired or replaced.

AMP

LENGTH

RATING      25ft

50ft          100ft

0-6

18

16

16

7-10

18

16

14

11-12

16

16

14

13-16

14

12

12

17-20

12

12

10

21-30

10

10

No

No list of safety guidelines can be
complete. Operating this tool may
require additional safety precau-
tions specific to your working
environment. Failure to use rea-
sonable caution while operating
this tool could result in serious
personal injury.

Summary of Contents for H3119

















Reviews:

Related manuals for H3119