background image

H3122 Classical Guitar Kit

-3-

We are proud to offer the Model H3122 Classical 
Guitar Kit. This kit is part of a growing Grizzly fam-
ily  of  fine  woodworking  products.  When  assem-
bled according to the guidelines set forth in this 
manual, you can expect years of enjoyment from 
this guitar.

We  are  pleased  to  provide  this  manual  with  the 
Model H3122. It was written to guide you through 
assembly,  review  safety  considerations,  and 
cover general information. It represents our effort 
to produce the best documentation possible.

If you have any comments regarding this manual, 
please write to us at the address below:

Grizzly Industrial, Inc.

C

/

Technical Documentation

P.O. Box 2069

Bellingham, WA  98227-2069

Most importantly, we stand behind our products. If 
you have any questions or parts requests, please 
call or write us at the location listed below.

Grizzly Industrial, Inc.

1203 Lycoming Mall Circle

Muncy, PA  17756

Phone: (570) 546-9663

Fax: (800) 438-5901

E-Mail: techsupport@grizzly.com
Web Site: http://www.grizzly.com

The  specifications,  drawings,  and  photographs 
illustrated  in  this  manual  represent  the  Model 
H3122  as  supplied  when  the  manual  was  pre-
pared.  However,  owing  to  Grizzly’s  policy  of 
continuous improvement, changes may be made 
at  any  time  with  no  obligation  on  the  part  of 
Grizzly.  For your convenience, we always keep 
current Grizzly manuals available on our website 
at www.grizzly.com. Any updates to products will 
be  reflected  in  these  manuals  as  soon  as  they 
are complete. Visit our site often to check for the 
latest updates to this manual!

 SECTION 2: INTRODUCTION

Summary of Contents for H3122

























Reviews: