background image

t23089 (Mfg since 11/10)

-2

-

use  proper  air  hose  for  the  tool. 
Make  sure  your  air  hose  is  in  good 
condition  and  is  long  enough  to    reach 
your work without stretching.

eXplosion  hazard.  do  not  exceed 
the  maximum  pressure  rating  for  the 
tool. doing so could cause it to explode, 
causing  serious  personal  injury.  inspect 
the  tool  before  use  for  cracks  or  any 
other signs of damage. replace if these 
are found. 

alWays  use  safety  glasses. 
Also  use  a  face  or  dust  mask  if  cutting 
operation is dusty. everyday eyeglasses 
only  have  impact  resistant  lenses,  they 
are not safety glasses.

Wear 

approved 

hearing 

protection.  Air  escaping  from 
pneumatic  tools  can  exceed  safe 
exposure  limits  and  may  cause  hearing 
damage with prolonged exposure.

safety instructions for 

pneumatic tools (continued)

like all machinery there is potential 

danger  when  operating  this 

machine.  accidents  are  frequently 

caused  by  lack  of  familiarity  or 

failure  to  pay  attention.  use  this 

machine  with  respect  and  caution 

to lessen the possibility of operator 

injury. if normal safety precautions 

are overlooked or ignored, serious 

personal injury may occur.

no  list  of  safety  guidelines  can  be 

complete.  every  shop  environment 

is  different.  always  consider  safety 

first,  as  it  applies  to  your  individual 

working  conditions.  use  this  and 

other  machinery  with  caution  and 

respect. failure to do so could result 

in serious personal injury, damage to 

equipment or poor work results.

secure WorK. use clamps or a vise 
to  hold  work  when  practical.  it  is  safer 
than  using  your  hand  and  frees  both 
hands to operate tool.

maintain  tools  With  care. 
Keep  tools  lubricated  and  clean  for 
best  and  safest  performance.  Follow 
instructions for lubricating and changing 
accessories.
 

Wear  proper  apparel.  do  not 
wear  loose  clothing,  gloves,  neckties, 
rings,  bracelets,  or  other  jewelry  that 
may  get  caught  in  moving  parts.  non-
slip  footwear  is  recommended.  Wear  a 
protective  hair  covering  to  contain  long 
hair.

reduce 

the 

risK 

of 

unintentional  use.  do  not  carry 
tool  with  hand  on  trigger  and  always 
disconnect from air when not in use.

Summary of Contents for T23089

















Reviews: