background image

For questions or help with this product contact Tech Support at (570) 546-9663 or techsupport@grizzly.com

MODEL T25448/T25449

DUST COLLECTOR

REMOTE SWITCH

INSTRUCTIONS

COPYRIGHT © FebRuaRY, 2013 bY GRIZZLY INDuSTRIaL, INC.

NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE

 OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.

 FOR MODeLS MaNuFaCTuReD SINCe 12/12  #TS15583  PRINTeD IN TaIwaN

Introduction

The  Model  T25448/T25449  Dust  Collector 
Remote Switch (

Figure 1) allows you to remotely 

turn a dust collector 

ON/OFF from a distance of 

up to 75 feet.

Read and understand this entire document before 
installation  to  make  sure  this  switch  box  fits  the 
intended application.

To ensure safe operation:
•  Only connect the switch box to power sup-

ply that meets the listed specifications.

• Do not connect the switch box to a dust 

collector with a motor that exceeds the 

listed specifications.

Specifications

Model T25448:
 

Power Supply ....................110V, 15a, 60 Hz

 

Outlet Type ................................. NeMa 5-15

 

Max. Dust Collector HP ..................... 1.5 HP

Model T25449:
 

Power Supply ................... 220V, 20a, 60 Hz

 

Outlet Type .................................NeMa 6-20

 

Max. Dust Collector HP ........................ 3 HP

Remote battery ..........................Type 23ae, 12V
Communication Type ........Radio Frequency (RF)
Max. Communication Distance ................... 75 ft.

• This remote switch is ONLY designed to 

be used on dust collectors with standard 

ON/OFF toggle or push-button switches—

not with magnetic switches.

• If you are unsure about the type of dust 

collector switch you have, contact the dust 

collector manufacturer for more informa-

tion.

• Using this switch box for applications 

other than dust collectors may cause the 

unit to fail and will void the warranty.

Replacement remote controllers (Model 

T25507) can be purchased by contacting 

Grizzly at (800) 523-4777. Before the new 

remote controller can be used, the switch 

box must be programmed to work with it 

(refer to Programming Switch Box on Page 

2 for detailed instructions).

Figure 1. Model T25448/T25449 remote switch 

components.

Switch 

box

Remote 

Controller

Summary of Contents for T25448

Page 1: ... the listed specifications Specifications Model T25448 Power Supply 110V 15A 60 Hz Outlet Type NEMA 5 15 Max Dust Collector HP 1 5 HP Model T25449 Power Supply 220V 20A 60 Hz Outlet Type NEMA 6 20 Max Dust Collector HP 3 HP Remote Battery Type 23AE 12V Communication Type Radio Frequency RF Max Communication Distance 75 ft This remote switch is ONLY designed to be used on dust collectors with stand...

Page 2: ... remote controllers and one remote con troller to operate several switch boxes The steps to accomplish any combination of these options are the same Before beginning read through the entire pro cedure to understand the required timing of the steps To program the switch box 1 Make sure the dust collector is NOT con nected to the switch box 2 Make sure the red receiving light on the switch box is il...

Page 3: ...ntroller ON button once to turn the dust collector ON The green power light on the switch box will also illumi nate see Figure 6 4 Press the remote controller OFF button once to turn the dust collector OFF The green power light on the switch box will turn OFF Un programming Switch Box If necessary the switch box can be un pro grammed so that it will not operated with any remote controller In such ...

Page 4: ...ector ON OFF switch ON 2 Properly connect dust collector to switch box Page 2 3 Connect switch box to correct power source Page 2 4 Reset wall circuit breaker Make sure breaker is in good condition and circuit is properly sized for dust collector in use 5 Refer to dust collector manual for troubleshooting contact dust collector manufacturer for technical help Troubleshooting Review the troubleshoo...

Reviews: