background image

GROUND ZERO GZDSP 4.80A-PRO 

 

 

 

DSP SERIES   

 

 

General mounting instructions 

 

 

As a precaution, it is recommended to disconnect the vehicles battery before mounting the amplifier.  

 

(Note: For new vehicles, disconnecting the battery might cause various errors in your vehicle´s electric 
system that can be cleared only by authorized service partners of your vehicle´s manufacturer! Please ask 
your service partner first before disconnecting the battery!) 

 

 

The power supply wire (+12 V) has to be protected within max. 20 cm / 8” by a main fuse holder with a 
fuse value matching the recommendation for your amplifier 

 

(Note: If there is more than one amplifier connected using this power wire, the main fuse value must be 
equal to the sum of the recommended fuses of all connected devices. However, make sure the diameter of 
your power wire will be enough for the required current!) 

 

 

If necessary, replace a defective fuse by a fuse with identical quality and value 

 

 

Never drill a hole to the vehicle´s gas tank or brake lines, to wirings or any other important vehicle parts! 

 

 

Never pass wires over sharp edges or vehicle parts due avoid any kind of damage 

 

 

Keep the wiring away from the antenna and electronic devices contributing to radio reception 

 

 

Lay the power supply wiring always separated from speaker wiring to avoid disturbance 

 

 

The amplifier contains a temperature protection circuit that turns the device off in case of overheating. After 
a certain cooling time, it will turn on automatically. To avoid heat build-up, enough air supply for cooling 
must be provided. Never cover the surface of the amplifier´s heatsink entirely 

 

 

The amplifier should NEVER be mounted onto a vibrating part or surface such as a subwoofer enclosure. 
This might lead to malfunction due to loosened electrical parts inside the amplifier. 

 

 

Some amplifiers offer a high-level input option, however if a pre-amplified output (RCA) is available (at the 
head unit), it is strongly recommended to make use of them. 

 
 
 
 

 
 
 

 

 

GROUND ZERO products are engineered in Germany

 

 
 

GROUND ZERO - international sponsor of 

 
 
 
 
 

Summary of Contents for GZDSP 4.80A-PRO













Reviews: