background image

1

.

5

 

Glossary

4

3

AC
Abbreviation for "Alternating Current"
DC
Abbreviation for "Direct Current"
Energy
Energy  is  measured  in  Wh  (watt  hours),  kWh  (kilowatt  hours)  or  MWh  (megawatt 
hours).  The  energy  is  the  power  calculated  over  time.  For  example,  your  inverter 
operates at a constant power of 4600 W for half an hour and then at a constant power 
of  2300  W  for  another  half  an  hour,  it  has  fed  3450Wh  of  energy  into  the  power 
distribution grid within that hour.
Power
Power  is  measured  in  W  (watts),  kW  (kilowatts)  or  MW  (megawatts).  Power  is  an 
instantaneous  value.  It  displays  the  power  your  inverter  is  currently  feeding  into  the 
power distribution grid.
Power rate
Power  rate  is  the  radio  of  current  power  feeding  into  the  power  distribution  grid  and 
the maximum power of the inverter that can feed into the power distribution grid.
Power factor
Power factor is the ratio of true power or watts to apparent power or volt amps. They 
are identical only when current and voltage are in phase than the power factor is 1.0. 
The  power  in  an  ac  circuit  is  very  seldom  equal  to  the  direct  product  of  the  volts  and 
amperes. In order to find the power of a single phase ac circuit the product of volts and 
amperes must be multiplied by the power factor.
PV
Abbreviation for photovoltaic.
Wireless communication
The external wireless communication technology is a radio technology that allows the 
inverter and other communication products to communicate with each other. The 
external wireless communication does not require line of sight between the devices 
and it is selective purchasing.

2

 

Safety

2

.

1

 

Intended Use

2

.

2

 

Qualification of skilled person 

2

.

3

 

Safety instruction 

The unit converts the DC current generated by the photovoltaic (PV) modules to grid-
compliant  alternating  current  and  performs  single-phase  feed-in  into  the  electricity 
grid.Growatt  8000MTLP-S,  Growatt    9000MTLP-S,  Growatt    10500MTLP-S  inverters 
are built according to all required safety rules. Nevertheless, improper use may cause 
lethal  hazards  for  the  operator  or  third  parties,  or  may  result  in  damage  to  the  units 
and other property.
Principle of a PV plant with thisGROWATT XXXX MTLP-S single-phase inverter

Position                                                            Description

A

B

C

D

E

F

PV modules

DC load circuit breaker

AC load circuit breaker

Energy meter

Utility grid

Growatt MTLP-S Inverter

A

B

C

D

E

F

The inverter may only be operated with a permanent connection to the public power 
grid. The inverter is not intended for mobile use. Any other or additional use is not 
considered the intended use. The manufacturer/supplier is not liable for damage 
caused by such unintended use. Damage caused by such unintended use is at the 
sole risk of the operator.
PV modules Capacitive Discharge Currents
PV modules with large capacities relative to earth, such as thin-film PV modules with 
cells on a metallic substrate, may only be used if their coupling capacity does not 
exceed 470nF. During feed-in operation, a leakage current flows from the cells to 
earth, the size of which depends on the manner in which the PV modules are installed 
(e.g. foil on metal roof) and on the weather (rain, snow). This "normal" leakage current 
may not exceed 50mA due to the fact that the inverter would otherwise automatically 
disconnect from the electricity grid as a protective measure.

This grid-tied inverter system operates only when properly connected to the AC -
distribution network. Before connecting the MTLP-S to the power distribution grid, 
contact the local power distribution grid company. This connection must be made only 
by qualified technical personnel to connect, and only after receiving appropriate 
approvals, as required by the local authority having jurisdiction.

The GROWATT MTLP-S Inverters is designed and tested according to international 
safety requirements

IEC61727/62116,INMETRO

;

 however, certain safety 

precautions must be observed when installing and operating this inverter. Read and 
follow all instructions, cautions and warnings in this installation manual. If questions 
arise, please contact Growatt's technical services at +86 (0)755 2747 1942.

Summary of Contents for 10500MTLP-S
























Reviews: