background image

10 

TROUBLE SHOOTING

In  most  situations,  the  Inverter  requires  very  little  service.  However,  if  Inverter  is  not 

able  to  work  perfectly,  please  refer  to  the  following  instructions  before  calling  your 

local dealer.

Should any problems arise, the LED on the front panel will be red and the LCD displays 

the  relevant  information.  Please  refer  to  the  following  table  for  a  list  of  potential 

problems and their solutions.

11 

SYSTEM FAULT

Ground Fault

Isolation Fault

1.

 The ground current is too high.

2.

 Unplug the inputs from the PV generator and check the peripheral AC system.

3.

 After the cause is cleared, re-plug the PV panel and check PV-Inverter status.

4. 

If the problem persists please call service.

1.

 Check the impedance is between PV (+) & PV (-) and the PV-Inverter is earthed. 

       The impedance must be greater than 8M.

2.

 If the problem persists please call service. 

 

No Utility

1. 

Grid is not connected.

2.

 Check grid connection cables.

3.

 Check grid usability. 

24

25

SPECIFICATIONS 

13

Input Data

Max. input current of the

MPP tracker

Max. DC power

Max. DC voltage

PV voltage range MPPT

Full load voltage

Initial feeding voltage

Max. number of parallel

strings

Number of MPP trackers

3600MTL

10A/10A

3800W

600V

120V-550V

250V-540V

150V

2/2

2(can parallel)

4200MTL

15A/15A

4400W

600V

120V-550V

250V-540V

150V

2/2

2(can parallel)

5000MTL

15A/15A

5200W

600V

120V-550V

250V-540V

150V

2/2

2(can parallel)

INVERTER FAILURE

 

12

PV Over Voltage

1.

 Check the open PV voltage, see if it is greater than or too close to 600VDC. 

2. 

If PV voltage is less than 600VDC, and the problem still occurs, please call 

        local service. 

Consistent Fault

1. 

Disconnect PV (+) or PV (-) from the input, restart the PV-Inverter.

2.

 If it does not work, call service. 

       > If there is no display on the panel, please check PV-input connections. 
          If the voltage is higher than 150V, call your local service. 

      > During periods of little or no sunlight, the PV-Inverter may continuously 
          start up and shut down. This is due to insufficient power generated to 
          operate the control circuits

Summary of Contents for Growatt 3600 MTL



















Reviews: