Growatt MAX 100KTL3-X LV Installation & Operation Manual Download

Page: 33 / 37

Error

Description

Suggestion

Error 200

AFCI Fault

1. After shutdown,check the panel

terminal.

2. Restart inverter.

3. Contact Growatt.

Error 201

Residual I High

1. Restart inverter.

2. Contact Growatt.

Error 202

PV Voltage High

1. Immediately disconnect the DC switch

and check the voltage.

2. Contact Growatt.

Error 203

PV Isolation Low

1. After shutdown, check if the panel
shell is reliably grounded.
2. Contact Growatt.

Error 204

PV Reversed

1. After shutdown, check PV input

terminals.

2. Contact Growatt.

Error 300

AC V Outrange

1. Check grid voltage.

2. Contact Growatt.

Error 301

AC terminals reversed

1. Check AC terminals.

2. Contact Growatt.

Error 302

No AC Connection

1. After shutdown,check AC wiring.
2. Contact Growatt.

Error 303

NE abnormal

1. After shutdown,ensure that the
ground wire is reliably connected.
2. Contact Growatt.

Error 304

AC F Outrange

1. Check the frequency is in the range of
specification or not.
2. Contact Growatt.

Error 400

DCI bias abnormal

1. Restart inverter.
2. Contact Growatt.

Error 401

DC Voltage High Fault

1. Restart inverter.

2. Contact Growatt.

Error 402

Output DC current too

high

1. Restart inverter.
2. Contact Growatt.

Error 403

Output current unbalance 1. Restart inverter.

2. Contact Growatt.

Error 404

Bus sample fault

1. Restart inverter.
2. Contact Growatt.

Error 405

Relay fault

1. Restart inverter.
2. Contact Growatt.

Error 406

Init model fault

1. Restart inverter.

2. Contact Growatt.

Error 407

AutoTest failure

1. Restart inverter.
2. Contact Growatt.

Error

Description

Suggestion

Error 408

NTC Temperature too high

1. Restart inverter.

2. Contact Growatt.

Error 409

Bus voltage abnormal 1. Restart inverter.

2. Contact Growatt.

Error 411

Communication fault

1. Restart inverter.
2. Contact Growatt.

Error 412

Temperature sensor

abnormal

1. Restart inverter.

2. Contact Growatt.

Error 413

IGBT drive fault

1. Restart inverter.
2. Contact Growatt.

Error 414

EEPROM fault

1. Check if shinemaster is abnormal.

2. Contact Growatt.

Error 415

Internal power test fail

1. Restart inverter.

2. Contact Growatt.

Error 416

Over current protected

1. Restart inverter.

2. Contact Growatt.

Error 417

System protocol abnormal 1. Restart inverter.

2. Contact Growatt.

Error 418

firmware version

abnormal

1. Restart inverter.

2. Contact Growatt.

Error 420

GFCI Module damage

1. Restart inverter.
2. Contact Growatt.

Error 421

CPLD abnormal

1. Restart inverter.
2. Contact Growatt.

Error 422

Sampling is inconsistent

1. Restart inverter.

2. Contact Growatt.

Error 425

AFCI self-test fault

1. Restart inverter.
2. Contact Growatt.

Error 426

PV current abnormal

1. Restart inverter.
2. Contact Growatt.

Error 427

AC current abnormal

1. Restart inverter.

2. Contact Growatt.

Error 428

Boost Short Out

1. Contact Growatt.

Error 429

Bus voltage softstart fail

1. Restart inverter.
2. Contact Growatt.

Summary of Contents for MAX 100KTL3-X LV






































Search results

Summary of Contents for MAX 100KTL3-X LV

Reviews:

Related manuals for MAX 100KTL3-X LV

Brands by name

Popular brands

Growatt MAX 100KTL3-X LV, Installation & Operation Manual

Search results

Summary of Contents for MAX 100KTL3-X LV

Reviews:

Related manuals for MAX 100KTL3-X LV

Brands by name

Popular brands