Growatt MID 10KTL3-X Installation & Operation Manual Download

Page: 19 / 23

Error Code

Fault Discription

Suggestion

Error 403

Output current

unbalance

1: After shutdown,Check the output current

is not balanced.

2: If the error message still exists, contact

manufacturer.

Error404

bus sample fault

1. Restart inverter.

2. If error message still exists,contact

manufacturer.

Error 405

Relay fault

1. Restart inverter.

2. If error message still exists,contact

manufacturer.

Error 406

Init model fault

1. Reset mode.
2. If error message still exists,contact
manufacturer.

Error 407

AutoTest failure

1. Restart inverter.

2. If error message still exists,contact

manufacturer.

Error 408

NTC Temperature too

high

1. After shutdown,Check the temperature,

normal restart the inverter.

2. If the error message still exists, contact

manufacturer.

Error 409

Bus voltage abnormal

1. Restart inverter.
2. If error message still exists,contact
manufacturer.

Error 410

Redundant sample
circuit of Insulation
values are different

1. Restart inverter.
2. If error message still exists,contact
manufacturer.

Error 411

Communication fault

1. After shutdown,Check communication
board wiring
2. If the error message still exists, contact
manufacturer

Error 412

Temperature sensor

connection is abnormal

1. After shutdown,Check the temperature

sampling module is connected properly.

2. If the error message still exists, contact

manufacturer.

Error 413

IGBT drive fault

1. Restart inverter.
2. If error message still exists,contact
manufacturer.

Error 414

EEPROM fault

1. Restart inverter.

2. If error message still exists, contact

manufacturer.

Error 415

Internal power test fail
(PV Power low)

1. Restart inverter.
2. If error message still exists,contact
manufacturer.

Error Code

Fault Discription

Suggestion

Error 416

Over current protected
by software

1. Restart inverter.

2. If error message still exists,contact

manufacturer.

Error417

Grid voltage sampling is

inconsistent

1. Restart inverter.
2. If error message still exists,contact
manufacturer.

Error 418

DSP and COM firmware
version unmatch

1. Check the firmware version.
2. If error message still exists,contact
manufacturer.

Error 419

Redundant sample
circuit of GFCI values
are different

1. Restart inverter.

2. If error message still exists,contact

manufacturer.

Error 420

GFCI Module damage

1: After shutdown,Check the leakage

current module.

2: If the error message still exists, contact

manufacturer.

Error 421

CPLD is abnormal

1. Restart inverter.

2. If error message still exists,contact

manufacturer.

Error 422

sampling is inconsistent

1. Restart inverter.

2. If error message still exists,contact

manufacturer.

Error 423

Battery Reverse Protect

Fault

1. Restart inverter.

2. If error message still exists, contact

manufacturer.

Error 424

Communication board

and control panel

sampling battery

voltage is inconsistent

1. Restart inverter.

2. If error message still exists, contact

manufacturer.

Error 425

AFCI self-test fault

1. Restart inverter.

2. If error message still exists, contact

manufacturer.

Summary of Contents for MID 10KTL3-X
























Search results

Summary of Contents for MID 10KTL3-X

Reviews:

Related manuals for MID 10KTL3-X

Brands by name

Popular brands

Growatt MID 10KTL3-X, Installation & Operation Manual

Search results

Summary of Contents for MID 10KTL3-X

Reviews:

Related manuals for MID 10KTL3-X

Brands by name

Popular brands