background image

This  manual  will  provide  detailed  product  information  and  installation  instructions  for 

users of model TL3-X series photovoltaic inverter of Shenzhen Growatt new energy Co., 

Ltd.  (hereinafter  referred  to  as  Growatt  new  energy).  Please  read  this  manual  carefully 

before using this product. Growatt new energy will not inform users of any changes to 

this manual.

MID 17KTL3-X1

MID 20KTL3-X1

MID 22KTL3-X1

MID 25KTL3-X1

MID 30KTL3-X

MID 33KTL3-X

MID 36KTL3-X

MID 40KTL3-X

WARNING

DANGER

Symbol

Description

DANGER

 indicates a hazardous situation which, if not avoided, will 

result in death or serious injury.

WARNING

  indicates  a  hazardous  situation  which,  if  not  avoided, 

could result in death or serious injury.

1.3 Symbols in this document

1.3.1 Symbols in this document

Warnings indicate hazards to equipment or personnel. It draws your attention to a certain
procedure or practice. If the procedure or practice is not properly implemented or
followed, it may cause damage or destruction of part or all of the Growatt device and/or
other equipment connected to the Growatt device, or cause personal injury.

1.3.2 

Markings on this product

CAUTION

CAUTION

  indicates  a  hazardous  situation  which,  if  not  avoided, 

could result in minor or moderate injury.

NOTICE

 is used to address practices not related to personal injury.

Information

 that you must read and know to ensure optimal 

operation of the system.

NOTICE

Information

Symbol

Explanation

Danger: Electricity!

Point of connection for grounding protection

Danger:Hot surface

!

Alternating Current (AC)

Danger:Flame

!

Direct Current (DC) 

Operation after 5 minutes

Read the manual

CE mark.

The inverter complies with the requirements of the applicable CE 
guidelines.

The inverter must not be disposed of with the household waste.

The inverter must be installed by professional electricians who are certified by relevant 

departments.  By  reading  this  manual  in  detail,  the  installer  can  install  the  MID  TL3-X 

series  inverter  correctly  and  quickly,  and  can  carry  out  troubleshooting  and 

communication system construction.

If  there  are  any  problems  during  the  installation  process,  the  installer  can  log  on  to 

www.growatt.com  to  leave  a  message  on  the  website  or  call  our  24-hour  service 

phone:

.

+86 755 2747 1942

1.2 Applicable personnel

1

 

Notes on this manual

1.1 Validity

Summary of Contents for MID 17KTL3-X1































Reviews: