background image

1

 

Notes on this manual

1.1 Validity

1

2

1.2 Target Group

This  manual  is  for  qualified  personnel.  Qualified  personnel  have  received  training  and 

have  demonstrated  skills  and  knowledge  in  the  construction  and  operation  of  this 

device. Qualified Personnel are trained to deal with the dangers and hazards involved in 

installing electric devices.

1.3 Additional information

Find further information on special topics in the download area at www.ginverter.com

The manual and other documents must be stored in a convenient place and be available 

at all times. We assume no liability for any damage caused by failure to observe these 

instructions. For possible changes in this manual, GROWATT NEW ENERGY CO.,LTD 

accepts no responsibilities to inform the users.

1.4.2 

Markings on this product

1.4 

Symbols in this document

1.4.1 Symbols in this document

A warning describes a hazard to equipment or personnel. It calls attention to a procedure 

or practice, which, if not correctly performed or adhered to, could result in damage to or 

destruction of part or all of the Growatt equipment and/or other equipment connected 

to the Growatt equipment or personal injury.

This manual describes the assembly, installation, commissioning and maintenance of the 

following Growatt Inverter model:

MIN 7000 TL-X/X(E)

MIN 8000 TL-X/X(E)

MIN 9000 TL-X

MIN 10000 TL-X

This manual does not cover any details concerning equipment connected to the MIN TL-

X( e.g. PV modules). Information concerning the connected equipment is available from 

the manufacturer of the equipment.

NOTICE

 is used to address practices not related to personal injury.

Information

operation of the system.

 that you must read and know to ensure optimal 

NOTICE

Information

WARNING

DANGER

Symbol

description

DANGER

result in death or serious injury.

 indicates a hazardous situation which, if not avoided, will 

WARNING

could result in death or serious injury.

  indicates  a  hazardous  situation  which,  if  not  avoided, 

Symbol

Explanation

Electrical voltage!

Point of connection for grounding protection

Risk of burns

Alternating Current (AC)

Risk of fire or explosion

Direct Current (DC) 

Operation after 5 minutes

Read the manual

CE mark.

The inverter complies with the requirements of the applicable CE 

guidelines.

The inverter must not be disposed of with the household waste.

   Isolation Switch

CAUTION

CAUTION

  indicates  a  hazardous  situation  which,  if  not  avoided, 

could result in minor or moderate injury.

 

Summary of Contents for MIN 10000TL-X
































Reviews: