background image

GROWSPAN

 GOTHIC PREMIUM HIGH TUNNELS

40

 108179_80_81_82_83_84H     Revision date: 01.08.21

ASSEMBLE THE ROLL-UP SIDE CONDUIT

Gather the parts:
•  Pipe 1.315'' x 75'' swaged (131S075) 
•  Tek screws (FA4482B) 

The roll-up side conduit assembly slides into the panel 

pocket. This assembly runs the length of the frame and 

serves as the center pipe that the panel wraps around 

when is open to ventilate the high tunnel. 

Complete these steps to assemble the roll-up side 

conduit.
1.  Locate all sections of pipe (131S075) needed to 

assemble the conduit. Consult the Side Profile 

diagram in the Quick Start section for details.

2.  Insert the swaged end of a pipe into the plain end of 

another pipe.

3.  Secure the pipe joint using a Tek screw (FA4482B) 

and tape over the screw using duct tape.

4.  Slide the conduit into the panel pocket and repeat 

steps 2-3 until the conduit is assembled.

5.  Allow approximately 12" to extend from the pocket 

at the end of the panel where the gearbox will be 

located. Pipe is trimmed to length once the twist-of-

the-wrist assembly is installed and used as a guide. 

 

ATTENTION:

 

Consult the Twist-of-the-Wrist 

Assembly procedure on the next page for diagrams 

that show an assembled roll-up side.

6.  Continue with the procedure that follows to attach the 

conduit to the roll-up side panels using fabric clips.

ATTACH CONDUIT TO ROLL-UP SIDE PANEL

Gather the parts:
•  Fabric clips CC6212 (One for each rafter position.)
•  Tek screws  (FA4482B)  

To this point, the roll-up side panel is secured to and 

hanging down from the aluminum u-channel. The 

assembled roll-up conduit is in the panel pocket.
1.  Using one CC6212 fabric clip at each rafter and 

FA4482B screws, secure the panel to the conduit.  

NOTE:

 Twist the conduit in a direction that wraps the 

panel toward the inside of the frame. This allows water 

to drain off the roll-up panel.

2.  Continue to roll the conduit until the excess panel 

is wound around the conduit and the lower edge is 

positioned at the base of the frame. 

3.  Temporarily anchor the conduit and panel to the 

frame or ground 

and repeat the steps to complete the 

installation of the roll-up side panel for the remaining 

side of the building up to this point

 

A

TTENTION: IF THERE IS A CHANCE THAT 

WIND WILL LIFT THE PANEL DURING THE NEXT 

PROCEDURE, SKIP TO AND COMPLETE THE 

"INSTALL THE ANTI-BILLOW ROPE" STEPS THEN 

RETURN TO AND COMPLETE THE TWIST-OF-THE-

WRIST STEPS THAT FOLLOW.

4.  Continue with the installation of the Twist-of-the-Wrist 

components for the roll-up sides.

Inside View

Ground Level

Roll side panels so they 

wrap on the inside or 

underside of the panel.

CC6212 

Fabric Clip

ROLL-UP SIDES —

ASSEMBLY & INSTALLATION

Summary of Contents for Gothic Premium 108179H






























































Reviews: