background image

GROWSPAN

 GOTHIC PREMIUM HIGH TUNNELS

8

 108179_80_81_82_83_84H     Revision date: 01.08.21

End Rafter

Interior 

Rafter

Baseboard is supplied 

by customer. Required 

for Drop-Down Sides.

Ground 

Level

Purlin 

Run

Ground 

Post

Actual frame may differ 

from example shown.

Angled 

Purlin

Customer-supplied 

End Framing

Customer-Supplied 

Ribbon Board – 

Required for Drop-

Down Sides

OVERVIEW

See illustration below to identify main parts of your 

high tunnel. Basic assembly steps include:
1.  Locate the required parts for each assembly 

procedure.

2.  Assemble the rafters and frame.
3.  Prepare and attach end panels, door panels, and 

corner baffles. 

4.  Install main cover.
5.  Attach the drop-down or roll-up panel and  

anti-billow ropes.

Gothic Premium High Tunnel:

H Models

ATTENTION:

 These instructions describe the installation of the optional 

ridge vent kit. (Additional purchase required.) The ridge vent kit is 

designed for use with the 

HF

 model (5.2 oz. cover) only. If you have the 

C model or did not purchase the ridge vent kit, skip those installation 

procedures when presented and continue as instructed.

Do not cut the film of the 

HC

 model to install ridge vent kit.

CUSTOMER-SUPPLIED END FRAME: 

Construct the end frame for the 

roll-up end panel using 4" x 4" wood posts. The doorframe materials are 

supplied by the customer. If quality 4" x 4" lumber at the lengths needed 

is not available, construct 2-ply wood beams using 2" x 6" boards secured 

together with exterior grade bolts and nuts. Center the doorframe in the 

end wall and dig the holes for the doorjambs. 

Stagger all joints. Do not align.

 

Use treated lumber and set in 

concrete for best results.

 

ENDWALL HEADER KITS: IF YOU PURCHASED AN ENDWALL 

HEADER KIT FOR YOUR HIGH TUNNEL, SEE PAGE 17 FOR 

ADDITIONAL DETAILS.

Summary of Contents for Gothic Premium 108179H






























































Reviews: