GrowSpan PB01720R4 Manual Download

Page: 12 / 31

GROWSPAN

™

ROUND PREMIUM HIGH TUNNELS

Revision date: 11.22.21

FINISH ROUGH EDGES

Gather the parts:
•  Duct tape (supplied by customer)
•  Metal file
1.  Check for any sharp edges on the frame and file them

smooth so they will not cut the cover.

2. Apply two layers of heavy duct tape on all pipe

connections and clamps that may contact the cover.

ANCHOR THE ASSEMBLED FRAME

At this point, anchor the high tunnel frame. Consult the

MUST READ document for anchoring information and

suggestions. Please call customer service at 1-800-245-

9881 for additional anchoring information.

CAUTION

: The anchor assembly is an integral part of

the high tunnel construction. Improper anchoring may

cause instability and failure of the structure to perform

as designed. Failing to anchor the shelter properly

will void the manufacturer’s warranty and may cause

serious injury and damage.

4. Use the steps of the previous procedure to install the

top, center purlin.

INSTALL TOP, CENTER PURLIN (continued)

5. Continue with the next procedure.

One pipe of the top, center purlin

installed. Continue by installing

the remaining pipe and clamps.

BASEBOARD INSTALLATION (RECOMMENDED)

Gather the parts:
• Treated or recycled plastic lumber (supplied by

customer).

Recommended: 2" x 6".

• 1/4" x 4" carriage bolts and nuts (may not work for

baseboards with a thickness greater than 1-1/2")

NOTE:

The following procedure describes one way

to install the recommended baseboards. The size

and type of the baseboard you choose may require

the use of alternative steps. When properly installed,

baseboards run the length of the frame.

On the outside of the frame, attach the first baseboard

to the ground posts using the 1/4" x 4" carriage bolts

(FAH009B) and nuts (FALB01B). Continue adding

baseboards to complete the first run. Splices are

made between posts as shown. Use a short section of

baseboard to secure separate baseboards at a splice.

Ground

Level

Inside of

Shelter

Outside of

Shelter

NOTE:

The boards should be at ground level or slightly

into grade to prevent the shelter from sinking and to

create a seal along the bottom. After installing the

baseboards, continue with these instructions.

This baseboard is

not included

with the shipment and must

be supplied by the customer. Treated or recycled plastic

lumber works well for a baseboard.

Recommended dimension: 2" x 6".

Summary of Contents for PB01720R4
































Search results

Summary of Contents for PB01720R4

Reviews:

Related manuals for PB01720R4

Brands by name

Popular brands

GrowSpan PB01720R4, Manual

Search results

Summary of Contents for PB01720R4

Reviews:

Related manuals for PB01720R4

Brands by name

Popular brands