日本語 (JP)
75
3. 取付
3.1 BACnet モ ジ ュ ールの接続
遮蔽, ツ イ ス ト ペ アー ケー ブルを 使用す る こ と
推奨接続
ケー ブルの適用
手順:
図
参照
1. 赤の コ ネ ク タ ー を タ ー ミ ナル プ ラ ス(位置 1)へ接
続
2. 緑 を タ ー ミ ナル マ イ ナ ス(位置 2)へ接続
3. グ レ ー を タ ー ミ ナル グ ラ ウ ン ド (位置3)へ接続
4. アース ク ラ ン プ で ケー ブル を留めて く だ さ い。 (
位置 4) ケーブル遮蔽(オ プ シ ョ ン)のアースは, 遮
蔽部 を アースへ接続す る こ と に よ り アース さ れま
す。
最大ケー ブル長 さ , セ ク シ ョ ン
参照
図 2
BACnet MS/TP セ グ メ ン ト の例
幾つかのBACnetマ ス タ ーが, 同 じ BACnet MS/TP
セ グ メ ン ト に接続 さ れる事があ り ます。
図 3
BACnet接続例
3.2 タ ー ミ ネーシ ョ ン レ ジ ス タ ー
タ ー ミ ネーシ ョ ン レ ジ ス タ ーは, CIM 3XX BACnetモ
ジ ュ ール上にあ り , 120オームの抵抗値です。
CIM 3XXは, タ ー ミ ネーシ ョ ン レ ジ ス タ ーの切 り 離 し
用に DIP ス イ ッ チ ( 2つ SW1 と SW2)を 有 し て い ま す。
切 り 離 し 状態(安全器)での DIPスイチ,
図参照。
図 4
タ ー ミ ネーシ ョ ン レ ジ ス タ ーの接続,
切 り 離 し
警告
CIM 3XXは SELV あ る いは SELV-E回路に
のみ 接続 し て く だ さ い。
BACnet
タ ー ミ ナル
カ ラ ー コ ー ド
デー タ 信号
プ ラ ス
赤
ポジ テ ィ ブ
マ イ ナ ス
緑
ネ ガ テ ィ ブ
グ ラ ウ ン ド
グ レ ー
グ ラ ウ ン ド
注
ANSI/ASHRAE BACnet規格に よれば, ケー
ブル遮蔽は, 正 し い運転を 確実に し , 且つ
アース異常電流を 防 ぐ ために, 一端を アー
スす る も のです。
T
M
04
4
2
7
4
10
09
LT
BR
LT
LT = Line Termination
BR = Bias Resistor
マ ス タ ー
マ ス タ ー
マ ス タ ー
ス レ ー ブ
ス レ ーブ
ス レ ー ブ
ス レ ー ブ
TM
04
50
5
9
25
09
位置
記述
1
BACnet タ ー ミ ナル プ ラ ス
2
BACnet タ ー ミ ナル マ イ ナ ス
3
BACnet タ ー ミ ナル グ ラ ウ ン ド
4
アース ク ラ ン プ
TM
04
17
0
1
09
08
2
3
1
4
SW1 SW2
Summary of Contents for CIM 3 Series
