background image

English (GB)

21

7.3 CU 100 control unit

CU 100 incorporates a motor-protective circuit 
breaker and is available with level switch and cable.

Single-phase pumps

Connect a run capacitor to the control unit. For 
capacitor size, see the table below:

7.4 Frequency converter operation

For frequency converter operation please observe 
the following information:
Requirements must be fulfilled.
Recommendations ought to be followed.
Consequences must be considered.

7.4.1 Requirements

The thermal protection of the motor must be 
connected.

Peak voltage and dU/dt must be in accordance 
with the table below. The values stated are 
maximum values supplied to motor terminals. 
The cable influence has not been taken into 
account. See data sheet for the frequency 
converter used regarding the actual values and 
cable influence on the peak voltage and dU/dt.

If the pump is an Ex-approved pump, check if the 
Ex certificate of the specific pump allows the use 
of a frequency converter.

Set the frequency converter U/f ratio according to 
the motor data.

Local regulations and standards must be fulfilled.

7.4.2 Recommendations

Before installing a frequency converter, calculate the 
lowest allowable frequency in the installation in order 
to avoid zero flow.

Do not reduce the motor speed to less than 30 % 
of rated speed. 

Keep the flow velocity above 1 m/sec.

Let the pump run at rated speed at least once a 
day in order to prevent sedimentation in the 
piping system.

Do not exceed the frequency indicated on the 
nameplate. In this case there is a risk of motor 
overload.

Keep the power cable as short as possible. The 
peak voltage will increase with the length of the 
power cable. See data sheet for the frequency 
converter used.

Use input and output filters on the frequency 
converter. See data sheet for the frequency 
converter used.

Use a screened power cable if there is a risk that 
electrical noise can disturb other electrical 
equipment. See data sheet for the frequency 
converter used.

7.4.3 Consequences

When operating the pump via a frequency converter, 
please be aware of these possible consequences:

The locked-rotor torque will be lower. How much 
lower will depend on the frequency converter 
type. See the installation and operating 
instructions for the frequency converter used for 
information on the locked-rotor torque available.

The working condition of bearings and shaft seal 
may be affected. The possible effect will depend 
on the application. The actual effect cannot be 
predicted.

The acoustic noise level may increase. See the 
installation and operating instructions for the 
frequency converter used for advice on how to 
reduce the acoustic noise.

Pump type

Run capacitor

[

μ

F]

[V]

SL1 and SLV

30

450

Max. repetitive peak 

voltage

[V]

Max. dU/dt 

U

N

 400 V

[V/

μ

 sec.]

650

2000

Summary of Contents for SL1.50












































Reviews: