ENGLISH
86
Searchingfordigitalterrestrial
TVchannelsautomatically
1
Open the menu with »
MENU
«.
2
Activate the menu item »Settings« with
»
OK
«.
3
Select the menu item »Source Setup« with
»
>
« or »
<
« and press »
OK
« to confirm.
4
Select the line »Advanced Settings« with
»
V
« or »
Λ
« and press »
OK
« to confirm.
5
Select the line »Active Antenna Power« with
»
V
« or »
Λ
«.
Switch on the antenna power supply for the
antenna with »
<
« or »
>
« (»On«)
Important:
7
The antenna power supply (5V ) may only
be switched on if the antenna is an active
indoor antenna with a signal amplifier and
it is not already supplied with a voltage via
a mains plug (or similar supply). Otherwise
you may cause a short circuit and irrepara-
bly damage your antenna.
6
Select the line »Automatic Channel Search«
with »
Λ
« or »
V
« and press »
OK
« to con-
firm.
7
Select the option »Air« with »
<
« or »
>
« and
press »
OK
« to confirm.
8
Select whether to search for digital or ana-
logue TV channels.
To to this press »
<
« or »
>
« to select the
option »Digital« or »Analogue« and confirm
with »OK«.
9
Press »
« (red) to start searching.
Notes:
7
When updating via the same satellites a
security query is displayed at the start of a
search.
7
If the previously stored channels should be
retained in the channel list and the new
channels found be added to it, then press
»
« (green).
7
If »
« (red) is pressed, the saved channels will
be deleted from the current channel list.
– The »Digital Searching« menu appears,
and the scan for TV channels begins.
– The search is complete as soon as the
message »Search is completed!« appears.
SPECIALSETTINGS
----------------------------------------------------------------------------------------
Note:
7
The search can be aborted with »
EXIT
«.
10
Switch to the Channel Editor with »
« (yel-
low) ;
or
press »
EXIT
« to end the setting.
Searchingfordigitalterrestrial
TVchannelsmanually
1
Open the menu with »
MENU
«.
2
Activate the menu item »Settings« with
»
OK
«.
3
Select the menu item »Source Setup« with
»
>
« or »
<
« and press »
OK
« to confirm.
4
Select the line »Advanced Settings« with
»
V
« or »
Λ
« and press »
OK
« to confirm.
5
Select the line »Active Antenna Power« with
»
V
« or »
Λ
«.
Switch on the antenna power supply for the
antenna with »
<
« or »
>
« (»On«)
Important:
7
The antenna power supply (5V ) may only
be switched on if the antenna is an active
indoor antenna with a signal amplifier and
it is not already supplied with a voltage via
a mains plug (or similar supply). Otherwise
you may cause a short circuit and irrepara-
bly damage your antenna.
6
Select the line »Manual Channel Search«
with »
Λ
« or »
V
« and press »
OK
« to con-
firm.
7
Select the option »Air« with »
<
« or »
>
« and
press »
OK
« to confirm
– »Manual Channel Search« menu is dis-
played.
8
Enter frequency (3-digit) directly with
»
1...0
«.
– Search will start.
– The search is finished when the channels
found appear in the list.
9
Press »
EXIT
« to end the setting.
Summary of Contents for Toronto 55 CLE 6545 AL
Page 1: ...EN Toronto 55 CLE 6545 AL ...
