www.gru
AC Vo
Opera
Storag
Relativ
Altitud
Over v
Batter
Auto O
Dimen
Safety
Operat
NOTIC
AC Cu
WARN
discon
clamp
1. Set t
4A
sele
rang
2. Pres
upotemper.com
O
oltage bandwid
ating Tempera
ge Temperatu
ve Humidity
de
voltage
ry
OFF
nsions/Weight
y
tion
ES: Read and
statement
manual pr
switch to t
urrent Measur
NING: Ensure t
nnected from th
measurements
the Function sw
range. If the ra
ect the higher r
ge if necessary
ss the trigger to
OPERATING INST
dth 50/400H
ture
14 to 12
re -14 to 1
90%(0
o
45%(4
Operat
Catego
Two 1.5
approx
t
200x5
For in
Overv
Degre
level,
etc., w
than
understand all
s listed in the s
rior to using this
the OFF positio
ements
that the test lea
he meter before
s.
witch to the 400
ange of the me
range first then
y.
o open jaw. Ful
TRUCTIONAC CLA
Hz (VAC)
22
o
F (-10 to 50
140
o
F (-30 to 6
o
C to 30
o
C); 75
40
o
C to 50
o
C)
ing: 3000m; St
ory III 600V
5V “AAA” Batte
x. 30 minutes
50x35mm/200g
door use and i
voltage Catego
ee 2. Category
, appliance, po
with transient o
Overvoltage C
l warning and
safety section o
s meter. Set th
on when the me
ads are
e making curre
0 or40A or
asured is not k
move to the lo
lly enclose one
KPF-02
AMP METER
0
o
C)
60
o
C)
5%(30
o
C to 40
o
torage 10,000m
eries
g
n accordance w
ory II, Pollution
y II includes loc
rtable equipme
overvoltages le
Cat. III
precaution
of this operatio
he function sele
eter is not in us
nt
known,
ower
e conductor
7 8
o
C);
m
with
cal
ent,
ess
n
ect
se.
to
The
read
DC/A
1. Ins
re
2. Se
3. Se
4. Co
5. Re
µA D
1. Ins
re
2.Se
3. Se
4. Re
at
5. To
To
6. Ap
7. Re
Resi
KPF-02
OPERATING
o be measured
clamp meter L
ding.
AC Voltage Me
sert the black t
ed test lead into
et the function s
elect AC or DC
onnect the test
ead the voltage
DC/AC CURRE
sert the black t
ed test lead into
et the function s
elect AC or DC
emove power f
the point wher
ouch the black
ouch the red te
pply power to t
ead the curren
istance and C
G INSTRUCTIONA
.
LCD will display
easurements
test lead into th
o the positive V
switch to the V
with the MOD
leads in parall
e measuremen
ENT MEASUR
test lead into th
o the positive µ
switch to the µA
C with the MOD
from the circuit
re you wish to m
test probe tip t
st probe tip to
the circuit.
t in the display
Continuity Mea
AC CLAMP METER
y the
he negative CO
V terminal.
V position.
E button.
el to the circuit
t on the LCD d
REMENTS
he negative CO
µA terminal.
A position.
DE button.
t under test, the
measure curre
to the negative
the positive sid
y.
asurements
www.grupotem
R
OM terminal and
t under test.
display.
OM terminal an
en open up the
nt.
e side of the cir
de of the circuit
mper.com
d the
d the
e circuit
rcuit.
t.
Yes