background image

Limited Warranty — N.A. Grain Products

The GSI Group, LLC. (“GSI”) warrants products which it manufactures, to be free of defects in materials and workmanship
under normal usage and conditions for a period of 12 months from the date of shipment (or, if shipped by vessel, 14
months from the date of arrival at the port of discharge). If, in GSI’s sole judgment, a product is found to have a defect in
materials and/or workmanship, GSI will, at its own option and expense, repair or replace the product or refund the
purchase price. This Limited Warranty is subject to extension and other terms as set forth below.

Warranty Enhancements:

The warranty period for the following products is enhanced as shown below and is in

lieu of (and not in addition to) the above stated warranty period. (Warranty Period is from date of shipment.)

Product

Warranty Period

Storage

Grain Bin Structural Design
▪ Sidewall, roof, doors, platforms and walkarounds
▪ Flooring (when installed using GSI specified floor support system for that floor)
▪ Hopper tanks (BFT, GHT, NCHT, and FCHT)

5 Years

Conditioning

Dryer Structural Design – (Tower, Portable and TopDry)
▪ Includes (frame, portable dryer screens, ladders, access doors and platforms)

5 Years

All other Dryer parts including:
▪ Electrical (controls, sensors, switches and internal wiring)

2 Years

All Non-PTO Driven Centrifugal and Axial Fans

3 Years

Bullseye Controllers

2 Years

Material
Handling

Bucket Elevators Structural Design

5 Years

Towers Structural Design

5 Years

Catwalks Structural Design

5 Years

Accessories (stairs, ladders and platforms) Structural Design

5 Years

Conditions and Limitations:

THERE ARE NO WARRANTIES THAT EXTEND BEYOND THE LIMITED WARRANTY DESCRIPTION SET FORTH
HEREIN; SPECIFICALLY, GSI DISCLAIMS ANY AND ALL OTHER WARRANTIES OF ANY KIND, EXPRESS OR
IMPLIED, INCLUDING, WITHOUT LIMITATION, WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE OR USE IN CONNECTION WITH: (I) ANY PRODUCT MANUFACTURED OR SOLD BY GSI,
OR (II) ANY ADVICE, INSTRUCTION, RECOMMENDATION OR SUGGESTION PROVIDED BY AN AGENT,
REPRESENTATIVE OR EMPLOYEE OF GSI REGARDING OR RELATED TO THE CONFIGURATION, INSTALLATION,
LAYOUT, SUITABILITY FOR A PARTICULAR PURPOSE, OR DESIGN OF SUCH PRODUCTS.

The sole and exclusive remedy for any claimant is set forth in this Limited Warranty and shall not exceed the amount paid
for the product purchased. This Warranty only covers the value of the warranted parts and equipment, and does not cover
labor charges for removing or installing defective parts, shipping charges with respect to such parts, any applicable sales
or other taxes, or any other charges or expenses not specified in this Warranty. GSI shall not be liable for any other direct,
indirect, incidental or consequential damages, including, without limitation, loss of anticipated profits or benefits. Expenses
incurred by or on behalf of a claimant without prior written authorization from the GSI warranty department shall not be
reimbursed. This warranty is not transferable and applies only to the original end-user. GSI shall have no obligation or
responsibility for any representations or warranties made by or on behalf of any dealer, agent or distributor. Prior to
installation, the end-user bears all responsibility to comply with federal, state and local codes which apply to the location
and installation of the products.

This Limited Warranty extends solely to products sold by GSI and does not cover any parts, components or materials used in conjunction with the
product, that are not sold by GSI. GSI assumes no responsibility for claims resulting from construction defects, unauthorized modifications,
corrosion or other cosmetic issues caused by storage, application or environmental conditions. Modifications to products not specifically
delineated in the manual accompanying the product at initial sale will void all warranties. This Limited Warranty shall not extend to products or
parts which have been damaged by negligent use, misuse, alteration, accident or which have been improperly/inadequately maintained.

Notice Procedure:

In order to make a valid warranty claim a written notice of the claim must be submitted, using the RMA form, within 60 days of discovery of a
warrantable nonconformance. The RMA form is found on the OneGSI portal.

Service Parts:

GSI warrants, subject to all other conditions described in this Warranty, Service Parts which it manufactures for a period of 12 months from the
date of purchase unless specified in Enhancements above.

(Limited Warranty - N.A. Grain Products_ revised 01 October 2020)

Summary of Contents for Bucket Elevator II Series









































Reviews: