background image

D-9107RExd

 

Digital Flame Proof Dual IR Flame Detector                

 

Installation and Operation Manual

   

                                                  

   

 

 

Page 6  

 

 

 

 

 

 

 

 

 

 

 

 

 

Fig. 9 

(7)  After connection, screw down the cable nut. 

5 Testing 

Warning: Power up only after all detectors are installed.  

The detector must be tested after installation and regular maintenance.  

Tests: 

(1)  Connect the detector to loop and 24VDC, it should be able to be registered by 

the control panel, and the red LED should flash periodically.   After the detector 

is powered up for 20 minutes, igniting an infrared light source at 1.5m distance 

in front of it, it shall report a fire alarm to the control panel within 30s and light 

the fire LED, and it should be reset from the control panel to standby state.  

(2)  Connect the detector to 24VDC only, the red LED should flash periodically in 

standby  state.  After  the  detector  is  powered  up  for  20  minutes,  igniting  an 

infrared light source at 1.5m distance in front of it, it shall give fire signal within 

30s and light the fire LED. 

After testing, reset the detector from control panel if it connects to the loop. If it’s not 

connected to loop, disconnect 24VDC power and re-power it up. Notify the proper 

authorities the system is back in operation. 

If a detector fails in testing, clean and test it again. If it still fails, return it for repair. 

6 Operation 

The address and classifications can be programmed using a handheld programmer. 

Please refer to the manual for the programmer. 

The range of address is 1~242. 

For setting classifications, number 1 represents class 1, number 2 for class 2 and 

number 3 for class 3. 

If the detector connects with the loop, it needs to be programmed with an address 

to be identified 

by the control panel.  If it doesn’t connect with the loop, no address 

setup is required. But terminal Z1 and Z2 must be connected with D1 and D2 in an 

Contact Signal cable outlet 

Loop and 24VDC cable inlet 

NPT 1/2 

M24

×

1.5 

Threaded entry type:M27

×

Summary of Contents for D-9107RExd












Reviews: