background image

-

19

NS3000 Series User Manual    rev.01 

TOP VIEW INTENAL SHELF BATTERY POSITION

 

I

 

FIG.2.5.B 

-

20

NS3000 Series User Manual    rev.01 

2.6 Control and Communication Cabling 

fig.  2-6  shown,  the  Relay  card  dry  contact  interface  (J2-J10),  communication  interface  (RS232  interface,  485 

interface and SNMP card interface) and parallel card position. 

 

 

Fig 2-6 Dry contact interface and communication interface 

The UPS accepts external signal from zero-voltage (dry) contacts connected through external dry contact terminals 

produced  and  phoenix  terminals.  Through  software  programming,  these  signals  become  active  when  these  contacts 

connect  to  +24V  to  ground.The  cables  connected  to  DRY  terminal  must  be  separated  from  power  cables.  Moreover, 

these  cables  should  be  double  insulated  with  a  typical  0.5  to  1.5  mm

2

 

cross-section  area  for  a  maximum  connection 

length between 25 and 50 meters. 

2.6.1 Dry Contact Interface of Battery and Environmental Temperature Detection (Optional) 

The input dry contact J2 and J3 can detect the temperature of batteries and environment respectively, which can be 

used in environment monitoring and battery temperature compensation 1. 

J2 and J3 interfaces diagram are shown in fig 2-7, the description of interface is in table 2-2. 

J2

J3

 

Fig 2-7 Diagram of J2 and J3 dry contact for temperature detecting 

  Table 2-2   

Position 

Name 

Purpose 

J2.1 

TEMP_BAT 

Battery temperature detection 

J2.2 

GND 

Power ground 

J3.1 

TEMP_ENV 

Environment temperature detection 

J3.2 

GND 

Power ground 

Note:   

Specified  temperature  sensor  is  required  for  temperature  detection  (R25=5kOhm,  B25/50=3275), 

please confirm with the manufacturer, or contact local maintenance engineers when placing an order. 

Summary of Contents for NS3000 10 kVA


























Reviews: