background image

 

14 

ZY120 1-3kVA User Manual EN rev.08.docx

 

5. Installation 

NOTICE

UPS operation in sustained temperature outside the range of 15-25

C (59

-77

F) 

reduces battery life.

 

5.1 Unpacking and Inspection 

1) Unpack the packaging and check the package contents. The shipping package contains:

 

● 1 UPS

 

● 1 user manual

 

● 1 RS232 cable

 

● 1 USB cable

 

● 1 input cable

 

● 1 output cable IEC 10A

 

● 1 output cable IEC16A (only on 2kVA and 3kVA)

 

● 1 CD with monitoring software UPSilon, setting software MTR e drivers

 

2) Inspect the appearance of the UPS to see if there is any damage during transportation. 

Do not turn on the unit and notify the carrier and dealer immediately if there is any damage 

or lacking of some parts.

 

5.2 Connect Input/Output Power 

5.2.1 Notes for installation

 

1) 

The UPS must be installed in a location with good ventilation, far away from water, 

inflammable gas and corrosive agents.

 

2) 

Ensure the air vents on the front and rear of the UPS are not blocked so as to ensure 

good ventilation.

 

3) 

Do not connect the UPS to loads of half-wave or similar absorption

 

4) 

Condensation  to  water  drops  may  occur  if  the  UPS  is  unpacked  in  a  very  low 

temperature environment. In this case it is necessary to wait until the UPS is fully 

dried inside out before proceeding installation and use. Otherwise there are hazards 

of electric shock.

 

5.2.2 Installation

 

5.2.2.1 Input protection

 

It’s  suggested  to  install  input  protection  breaker  upstream  the  UPS.  Here  below  the 

references:

 

ZY120-1K / ZY120-1K-KS: 10A-2P curve C 250Vac

 

ZY120-2K / ZY120-2K-KS: 16A-2P curve C 250Vac

 

ZY120-3K / ZY120-3K-KS: 20A-2P curve C 250Vac

 

Summary of Contents for ZY120
































Reviews: