background image

                                                                                Important Safety Instructions 

ZY120 1-3kVA User Manual EN rev.08.docx

 

 

 

DO NOT CONNECT equipment that could overload the UPS or demand DC current from the 
UPS, for example: electric drills, vacuum cleaners, laser printers, hair dryer or any appliance using 
half-wave rectification.

 

Storing magnetic media on top of the UPS may result in data loss or corruption.

 

Turn off and isolate the UPS before cleaning it. Use only a soft cloth, never liquid or aerosol 
cleaners

 

 

 

 

2. Introduction 

Congratulations on your choice of the uninterruptible power system(UPS), the UPS comes in 

nominal power ratings of 1000VA,2000VA and 3000VA. It is designed to provide conditioned 

power to microcomputers and other sensitive electronic equipment.

 

When it is generated, alternating current is clean and stable. However, during transmission and 

distribution it may be subject to voltage sags, spikes and complete power failure that may interrupt 

computer operations, cause data loss and even damage equipment. The UPS protects equipment 

from these disturbances.

 

The UPS is a compact, on-line UPS. An on-line UPS continuously conditions and regulates its 

output voltage, whether utility power is present or not. It supplies connected equipment with clean 

sinewave power. Sensitive electronic equipment operates best from sinewave power.

 

For ease of use, the UPS features a LCD display to indicate all information for UPS, and provide 

kinds of function buttons.

 

 

 

1KVA                        2KVA/3KVA

 

Summary of Contents for ZY120
































Reviews: