background image

4

• Use only with the battery pack supplied.
• Leaks from battery cells can occur under 

extreme conditions. If the liquid gets on 
your skin wash immediately with soap 
and water. If the liquid gets into your 
eyes, flush them immediately with cold 
water for a minimum of 10 minutes and 
seek urgent medical attention.

• Protect the battery against excessive 

temperatures and fire.

• Do not store the battery outside for 

prolonged periods of time over the 
winter months.

 

• Do not dispose of the battery 

pack into household waste, fire or 
water. The battery pack should be 
collected, recycled or disposed of in 
an environmentally friendly manner. 
Discharge your battery pack by 
operating your Robot Mower. Remove 
the battery pack from the housing and 
cover the battery pack connections with 
heavy duty ventilation tape to prevent a 
short circuit and energy discharge. Do 
not attempt to open or remove any of 
the components.

 Service:

• Check all visible fixing screws and nuts, 

especially on the cutter disc, to ensure 
they are tightened properly.

• The mower and its charge station 

should be periodically checked and 
cleaned and kept free of debris and 
obstructions. Note that some garden 
creatures such as spiders, insects, 
snails and slugs can nest or hibernate 
within crevices of the mower. These can 
attract small creatures / rodents that can 
damage the mower if not deterred.

• Before using the mower and after 

any impact, check for signs of wear 
and damage and repair or replace as 
necessary.

• Use only genuine replacement parts. 

This will ensure that the safety of the 
mower is maintained.

• Do not attempt to repair any damaged 

parts on the mower unless you are 
qualified to do so.

• Please contact Gtech on 01905 345891 

if you have any queries about your 
product.

  Intended Use:

• This product is intended for DOMESTIC 

USE ONLY.

 

4719_Robot_Mower_manual_aw3.indd   4

4719_Robot_Mower_manual_aw3.indd   4

20/04/2021   16:21

20/04/2021   16:21

Summary of Contents for RCLM001

































Reviews: