20
Step 2
Make sure the control box power switch is in the
OFF
position. The ON/OFF Switch is located on the bottom of
the control box. Remove the control box cover and slide
the battery into position with its terminals to the
RIGHT
(
see illustration
). Connect the
BLACK
battery wire to the
NEGATIVE
(
–
) battery terminal. Connect the
RED
battery
wire to the
POSITIVE
(
+
) terminal.
Pay close attention to
the color of the wires. If the wires are connected incorrectly,
the control board will be damaged
.
NEVER
insert the
battery with the terminals to the left.
Mounting the Control Box
Step 3
Strip approximately 3/16" of insulation from each
wire of the power cable. Twist each exposed wire
tightly (there are seven [7] wires inside the power cable
sheath). Loosen sealing nut on strain relief hub at
bottom of control box. Insert power cable into control
box through strain relief. Thread approximately 6"
of the power cable into the control box and retighten
sealing nut until the power cable locks into place.
Step 1
Mount the control box using the screws (
provided
) or another
secure mounting method. The control box must be mounted at
least
3 feet above the ground
to protect it from rain splash,
snow, etc., and at least
3 feet from an AC power source to
prevent electrical interference
.
RED wire to POSITIVE (
+
) terminal
BLACK wire to NEGATIVE (
—
) terminal
RED
BLACK
Sealing Nut
Hub
Lock Nut
Strain Relief
NOTE:
The battery that came with your GTO/PRO®
3000,
MUST
be placed in the top (horizontal) battery
slot with the terminals on the
RIGHT
. The extra
(vertical) battery slot is for an optional second battery.
An optional second battery can be used for solar and/or
high traffic applications, if needed..
Use mounting
holes and screws
provided to mount
control box to a
secure surface.
1
ON
2 3 4 5 6 7
1
ON
2 3 4
15
18VAC
RECEIVER
BAT+
SWITCH
FUSE
ALARM
SWITCH
DUAL
MODES
SET
LIMIT
LEARN
TRANSMITTER
MODES
ON
OFF
ON
OFF
1 2 3 4 5 6 7
1 2 3 4
BAT–
SOLAR RELAY OUT
SLAVE INPUTS
GRN WHT BLUE
BRN ORG
RED BLK
NC RLY-COM NO
MASTER INPUTS
GRN WHT BLUE
BRN ORG
RED BLK
COM COM
CY
CL
E
CL
OS
E
SA
FE
TY
EX
IT
/
OP
EN
SHADOW LO
OP
CL
OS
E
ED
GE
OP
EN
ED
GE
BLK
GRN
RED
+
–
~
~
12'
10'
8'
14'
16'
GATE LENGTH
800-543-GATE
www.gtoinc.com
GTO, Inc.
3121 Hartsfield Rd
Tallahassee, FL 32303
Operator Power Cable
12 V Battery (Included)
Strain Relief
1
ON
2 3 4 5 6 7
1
ON
2 3 4
15
18VAC
RECEIVER
BAT+
SWITCH
FUSE
ALARM
SWITCH
DUAL
MODES
SET
LIMIT
LEARN
TRANSMITTER
MODES
ON
OFF
ON
OFF
1 2 3 4 5 6 7
1 2 3 4
BAT–
SOLAR RELAY OUT
SLAVE INPUTS
GRN WHT BLUE
BRN ORG
RED BLK
NC RLY-COM NO
MASTER INPUTS
GRN WHT BLUE
BRN ORG
RED BLK
COM COM
CY
CL
E
CL
OS
E
SA
FE
TY
EX
IT
/
OP
EN
SHADOW LO
OP
CL
OS
E
ED
GE
OP
EN
ED
GE
BLK
GRN
RED
+
–
~
~
12'
10'
8'
14'
16'
GATE LENGTH
800-543-GATE
www.gtoinc.com
GTO, Inc.
3121 Hartsfield Rd
Tallahassee, FL 32303
NOTE:
The battery that came with your GTO/PRO® 3000 ,
MUST
be placed horizontally battery with the terminals on the
RIGHT
. If an optional second battery is needed, both batteries
must be placed vertically with terminals at the bottom. An
optional second battery can be used for solar and/or high traffic
applications, if needed..
Single Battery
Installed Horizontally
with terminals on the right.
Dual Batteries
Installed Vertically
with terminals on bottom.
