GTO /PRO SW-300 Installation Manual Download

Page: 3 / 45

Gate Operator Class Categories ------------------------------------------------------------inside cover
Units and Standards Conversion Chart ---------------------------------------------------inside cover

PLEASE READ THIS FIRST! --------------------------------------------------

page iii

Important Safety Instructions --------------------------------------------------

page 1

Disconnecting the Operator -----------------------------------------------------------page 1

Important Safety Instructions for the Consumer ------------------------------------page 2

Secondary Means of Protection Against Entrapment ------------------------------page 5

Required Safety Precautions for Gates -----------------------------------------------page 6

Warning Signs and Labels -------------------------------------------------------------page 7

Installation --------------------------------------------------------------------------

page 8

Parts List ---------------------------------------------------------------------------------page 8

Technical Speciﬁcations -------------------------------------------------------------page 11

Installation Overview ---------------------------------------------------------------- page 12

Installation of the Mounting Hardware ----------------------------------------------page 13

Mounting the First Operator -----------------------------------------------------------page 17

Installing the Second Operator --------------------------------------------------------page 17

Installation of the Closed Position Stops --------------------------------------------page 18

Mounting the Control Box -------------------------------------------------------------page 20

Connecting the Operator Power Cables ----------------------------------------------page 21

Powering the System --------------------------------------------------------------

page 22

Solar Chart -------------------------------------------------------------------------------page 22

Connecting the Transformer -----------------------------------------------------------page 23

Control Board Settings ----------------------------------------------------------

page 25

Main DIP Switches ---------------------------------------------------------------------page 25

Dual Mode DIP Switches --------------------------------------------------------------page 26

Setting Closed Position Limits --------------------------------------------------------page 27

Setting Your Personal Transmitter Code ---------------------------------------------page 28

Obstruction Sensitivity -----------------------------------------------------------------page 29

Installing the Receiver -----------------------------------------------------------

page 29

Connecting Additional Safety Devices ----------------------------------------

page 30

Connecting Accessories ----------------------------------------------------------

page 32

Push to Open Installation --------------------------------------------------------

page 33

Setting Open Position Limits ----------------------------------------------------------page 34

Maintenance & Troubleshooting Guide --------------------------------------

page 36

Repair Service ---------------------------------------------------------------------

page 38

Column Installation Information ----------------------------------------------

page 39

Accessory Catalog ----------------------------------------------------------------

page 40

Table of Contents

KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE

Summary of Contents for /PRO SW-300














































Search results

Summary of Contents for /PRO SW-300

Reviews:

Related manuals for /PRO SW-300

Brands by name

Popular brands

GTO /PRO SW-300, Installation Manual

Search results

Summary of Contents for /PRO SW-300

Reviews:

Related manuals for /PRO SW-300

Brands by name

Popular brands