32
Step 3
With the gate in the desired open position PRESS & HOLD the “LEARN MAST LIMIT" button on the control board for 5
seconds.
Step 4
Press the transmitter button and allow the gate to return to the
closed position. YOUR GATE’S OPEN POSITION LIMIT IS
NOW PROGRAMMED.
TESTING YOUR OPEN LIMIT SETTING:
Press your entry transmitter and allow your gate to open. If the
OPEN position is not correct or needs to be changed, you will
need to CLEAR your OPEN LIMIT settings and follow steps
one () to four (4) again.
CLEARING PROGRAMMED
OPEN LIMIT SETTING:
If you make a mistake and set the limit at the wrong position
– press your transmitter to return the gate to the fully closed
position, then press and hold the "LEARN MAST LIMIT"
button for 5 seconds. This will clear the memory for the
open limit position. Follow steps one () to four (4) again.
1
2
3
4
O
N
D
IP
STATUS
LEARN RMT
LEARN
MAST LIMIT
LEARN
SLV LIMIT
S3
S4
S2
ART OFF
G OFF
PULL
EN DLY.
OFF
OFF
ON
ON
PUSH
SIMULT.
ON
ON
120 MIN
MAX
CLOSE TIME
STALL FORCE
Learn Master Limit
Button
Step 4
Make sure the control box power switch
is
OFF
. Use a small screwdriver to
move the
Number 3
DIP switch from
the factory setting (OFF / Pull-To-
Open) to
ON for Push-To-Open
. Turn
power switch
ON
. The control board is
now configured to
push
the gate open.
Step 1
Confirm that the power switch is in the ON position, and the gate is in the CLOSED POSITION.
Step 2
Activate your opener by pressing the entry transmitter button. Your gate should now be moving from the closed position
toward the open position. Prepare to STOP gate by pressing the entry transmitter button again when the gate reaches the
desired open position. This step may be repeated until desired open position is achieved. Once the desired OPEN position has
been achieved, proceed to Step 3.
ON
OFF
DIP#3
ON
Push-to-open operation.
OFF Pull-to-open operation (factory setting).
1
ON
DIP
2 3 4
1 2 3 4
ON
O
FF
S
O
FT
S
TA
R
T
O
FF
W
A
R
N
IN
G
O
FF
O
P
E
N
P
U
LL
S
LV
O
P
E
N
D
LY
.
M
O
D
E
1
O
FF
O
N
O
N
P
U
S
H
S
IM
U
LT
.
O
N
1
2
0
M
IN
M
A
X
A
U
TO
CL
OSE
TIME
ST
A
LL
FO
R
C
E
1 2 3 4
ON
O
FF
S
O
FT
S
TA
R
T
O
FF
W
A
R
N
IN
G
O
FF
O
P
E
N
P
U
LL
S
LV
O
P
E
N
D
LY
.
M
O
D
E
1
O
FF
O
N
O
N
P
U
S
H
S
IM
U
LT
.
O
N
1
2
0
M
IN
M
A
X
A
U
TO
C
LOS
E
TIME
ST
A
LL
FO
R
C
OR
C
1 2 3 4
ON DIP
O
FF
O
FF
P
U
LL
D
LY
.
O
FF
O
FF
O
N
O
N
P
U
S
S
IM
U
O
N
O
N
1
2
0
M
IN
Setting the Open Position Limit
Push to Open Installation
