GTO SW-2500 Installation Manual Download

Page: 3 / 43

Gate Opener Class Categories -------------------------------------------------------------inside cover
Units and Standards Conversion Chart ---------------------------------------------------inside cover

PLEASE READ THIS FIRST! --------------------------------------------------

page iii

Important Safety Instructions --------------------------------------------------

page 1

Disconnecting the Opener -------------------------------------------------------------page

Important Safety Instructions for the Consumer ------------------------------------page 2

Secondary Means of Protection Against Entrapment ------------------------------page 5

Required Safety Precautions for Gates -----------------------------------------------page 6

Warning Signs and Labels -------------------------------------------------------------page 7

Installation --------------------------------------------------------------------------

page 8

Parts List ---------------------------------------------------------------------------------page 8

Technical Specifications -------------------------------------------------------------page 0

Installation Overview ------------------------------------------------------------------ page

Installation of the Mounting Hardware ----------------------------------------------page 2

Mounting the Opener -------------------------------------------------------------------page 6

Installation of the Closed Position Stop ---------------------------------------------page 6

Mounting the Control Box -------------------------------------------------------------page 7

Connecting the Power Cable ---------------------------------------------------------page 8

Powering the System --------------------------------------------------------------

page 19

Solar Chart -------------------------------------------------------------------------------page 9

Connecting the Transformer -----------------------------------------------------------page 2

Control Board Settings ----------------------------------------------------------

page 22

DIP Switches ----------------------------------------------------------------------------page 22

Setting the Closed Position ------------------------------------------------------------page 23

Stall Force -------------------------------------------------------------------------------page 24

Setting Your Personal Transmitter Code -------------------------------------

page 25

Installing the Receiver -----------------------------------------------------------

page 26

Connecting Additional Safety Devices ----------------------------------------

page 27

Connecting Accessories ----------------------------------------------------------

page 29

Push to Open Installation --------------------------------------------------------

page 31

Maintenance & Troubleshooting Guide --------------------------------------

page 34

Repair Service ---------------------------------------------------------------------

page 37

Column Installation Information ----------------------------------------------

page 37

Accessory Catalog ----------------------------------------------------------------

page 38

Table of Contents

KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE

Summary of Contents for SW-2500












































Search results

Summary of Contents for SW-2500

Reviews:

Related manuals for SW-2500

Brands by name

Popular brands

GTO SW-2500, Installation Manual

Search results

Summary of Contents for SW-2500

Reviews:

Related manuals for SW-2500

Brands by name

Popular brands