background image

4

IMPORTANT SAFETY INSTRUCTIONS

III. After Installation

  . 

Attach the 

warning signs

 (

included

) to each side of the gate to alert the public of automatic gate operation.  It is 

your responsibility

 to post warning signs on both sides of your gate.  If any of these signs or warning decals become 

damaged, illegible or missing, replace them immediately.  Contact GTO/PRO for free replacements.

  2. 

The gate is automatic and could move at any time, posing a serious risk of entrapment.  No one should be in contact 
with the gate when it is moving or stationary.

 
  3. 

Do not attempt to drive into the gate area while the gate is moving; wait until the gate comes to a complete stop.

  4. 

Do not attempt to "beat the gate" while the gate is closing. This is extremely dangerous.

  5.   Do not allow children or pets near your gate.

  Never let children operate or play with gate controls

.  Keep the 

remote controls away from children and unauthorized users; store controls where children and unauthorized users do 
not have access to them. 

  6. 

KEEP GATES PROPERLY MAINTAINED

. Always turn power to opener OFF before performing any 

maintenance. Clean the push-pull tube with a soft, dry cloth and apply silicone spray to it at least once per month. 

  7. 

Service the gate and gate opener regularly. Grease hinges, spray push/pull tube with high quality silicone spray and 
replace the battery every 3-5 years.

  8.   To operate this equipment safely, YOU must know how to disconnect the opener for manual gate operation
 

 

(

see page 1

).  If you have read the instructions and still do not understand how to disconnect the opener, contact the 

GTO/PRO Service Department.

  9.   Disconnect the opener 

ONLY

 when the power is 

TURNED OFF

 and the gate is 

NOT

 moving.

  0. 

Make arrangements with local fire and law enforcement for emergency access.

  .   Distribute and discuss copies of the 

IMPORTANT SAFETY INSTRUCTIONS

 section of this manual with all 

persons authorized to use your gate. 

  2. 

IMPORTANT: Save these safety instructions. Make sure everyone who is 
using or in the vicinity of the gate and gate opener are aware of the dangers 
associated with automated gates. In the event you sell the property with the 
gate opener or sell the gate opener, provide a copy of these safety instructions 
to the new owner. 

    Should you lose or misplace this manual, a copy can be obtained by 

downloading one from the GTO/PRO web site (www.gtopro.com), by 
contacting GTO/PRO, at 3121 Hartsfield Road, Tallahassee, Florida 32303 
or by calling 1-800-543-4283 and requesting a duplicate copy. One will be 

Summary of Contents for SW-2500












































Reviews: