IMPORTANT – Regular maintenance is unavoidable for
constant operational reliability and keeping the original
device output.
1)
Keep all screws and nuts tightened so that you were sure
the device is in an operation-reliable condition. Regular
maintenance is necessary for safety and trouble-free
operation.
2)
Never store the device with fuel in closed rooms as the
evaporating fuel may ignite.
3)
It is necessary to let the device cool down and empty fuel
from it before storing in closed rooms.
4)
In order to minimise the risk of fire keep the engine
and muffler and the fuel tank clean and with no grass,
leaves and fats. Do not store the grass cut with the
mower.
5) For safety reasons, avoid using a device with a worn
or damaged parts. Replace any faulty parts with new
ones, do not repair them. Use original spare parts and
original spare knives only.
Parts with quality different from the one prescribed
may damage the device and threaten your safety.
6)
If it is necessary to empty the fuel tank do it outside and
with cold engine.
7)
Wear solid protective gloves at assembly and adjustment
of knives.
8)
Check correct direction of rotating and balance of knives
after sharpening.
9)
Regularly check wear and pollution of the self-closing
cover and grass catcher.
10) When you must transport the device, carry it in hands or
incline it always wear safety gloves.
Always hold the device at places guaranteeing safe holding.
Take into account the weight of the device and its distribution.
Č
LEANING
Clean the device with water, remove the grass and mud from
inside before each use – it will prevent from impurities getting dry
and problems at next starting.
The painting inside the housing may wear down in the course
of time. In order to prevent later corrosion of the device use
anti-corrosive paint for the worn-down spots.
Remove the gearbox cover and clean the space around belt
pulleys and drive belts with a brush or compressed air once or
twice a year.
You should clean the inside of the drive wheels once per
season. Disassemble both wheels. Clean the cog wheels and
their edges off the grass and other impurities with compressed
air or a brush.
KNIFE DISASSEMBLY
For purpose of cleaning / sharpening / replacement
Attention!!! It is necessary to first disconnect the spark plug
before disassembly.
Release the screw at disassembly of the knives.
Re-assemble according to the picture. Tighten the screws. Torsion
moment of 40 Nm. You should also replace the screw at
replacement of knives.
OIL CHANGE
The stopper for oil emptying is placed under the engine. Make
sure you have a container for oil catching prepared and
disassemble the stopper. As soon as the oil flows out insert a
new stopper with a washer and wipe oil remnants.
Add new SAE30 oil to the tank. Measure the oil level with a
clean gauge. The oil must reach between min. and max.
marking on the gauge. Make sure you do not overfill the tank.
Start the engine and let running for a short time. Then switch
it off, wait for a minute and measure the oil level. If necessary,
add some oil.
Spark plug
When the engine cools down disassemble the spark plug with
the key supplied, clean it with a wire brush and adjust the
distance to 0.75 mm (0.030") through a feeler gauge. Then re-
fit the spark plug. Make sure you do not tighten it too firmly.
(alternatively:
(Bosch WR 7 DC); (NGK BPR 6 ES)
Air filter
Loosen the filter cap and remove the foam filter element. It is
necessary to re-fit the filter cap to prevent entering of foreign
bodies to the suction inlet.
FUEL TANK AND CARBURETTOR EMPTYING
Put a container allowing petrol storage under the carburettor.
Work with a funnel to prevent petrol spilling.
Disassemble the drain screw, then adjust the fuel valve tie rod to
the ON position.
Re-fit the drain screw with a packing ring after fuel tank
emptying. Tighten the screw firmly.
STORAGE
The petrol must not remain in the fuel tank for more than 1
month. Regularly clean the mower and store it to a dry,
closed room.
ENVIRONMENT
You should pay special attention to the following points for
environment protection:
•
Always use clean unleaded petrol.
•
Always use a funnel and/or can with level regulation to
prevent fuel spilling while refuelling.
•
Do not fill the fuel tank up to the edge.
•
Do not let the engine oil overflow.
16