GÜDE 410/10/50 230 V, Operating Instructions Manual

 
Unscrew the drain screw is now firmly back on and fill 
oil up to the mark on the dipstick 
 

 In winter we recommend a lubricity oils to start 

during the cold season to help! 

Handling (pic. 1,2) 

Turn the compressor never about the power, 

otherwise no discharge of the unit is done. Without 
discharge, the electric motor through the back pressure 
damage! 

The plug needs to be pulled out of socket before 

each adjusting or maintenance of the compressor. 
 
Switching on or off 

•

The compressor can be switched on by pulling the 
switching button and switched off by pushing the 
button.

 
Working pressure control 

•

The working pressure can easily be adjusted, turn the 

rotary knob 

in the + direction

, by this 

the working 

pressure 

is 

increased

. Turn the rotary knob 

in the – 

direction

, by this 

the working pressure is 

decreased. There is an automatic safety valve 
releasing pressure at overpressure. The pressure 
can be released by hand by pulling the valve ring.

ATTENTION:  
 

Ensure necessary volume delivered of your pneumatic 
appliance! The pressure itself IS NOT decisive for a 
faultless or sufficient operation. Switching the compressor 
on for a short time following a long shut-down without using 
it is normal! 
Have any scheduled repairs explicitly executed by a trained 
professional staff. 

 
Inspections and maintenance (pic. 9) 

 
Always pull the plug out of socket before each work on the 
appliance. Before any long period of not using of the 
compressor it is necessary to give a few oil drops on the air 
filter washer – compressor cylinder walls will prematurely be 
lubricated at the next start. 

•

To clean the plastic parts, use a damp cloth. Do not 
use any cleaners, solvents or sharp objects. 

•

After each use, remove any settled dust from air holes and 
mobile parts with a soft brush. 

Regularly lubricate all mobile metal parts with oil. 

 
After each use 

Remove dust from air holes and mobile parts.  
 

Regularly 

Lubricate mobile metal parts with oil (multipurpose oil) 

Check whether all screws are firmly tightened.  
Regularly (at least once a month) remove condensation from the air 
jet otherwise your rust guarantee will expire – apart from this 
activity, the compressor is maintenance-free  
(due to the air jet surface, the condensation can get brown). 
1. 

Pull the plug out of socket! 

2. 

Open the sludge valve 

(pic. 9/a)

 at low voltage in the air jet 

(max. 1 bar) and completely empty the condensation (use a 
suitable container)  

3. 

Close the valve. 

Overheating fuse: 

 
If the compressor has any technical defect or is burdened with a 
continuous run the current supply is automatically interrupted by a 
thermal switch. Should this situation occur, it is suitable to 
disconnect the compressor from network and leave it cool down for 
app. 5 minutes. If the compressor fails to start after some time of 
working leave it cool down for other 3 minutes. 
 

Air-pressure switch: 

 
The compressor is fitted with an automatic air-pressure switch that 
is switched off by the compressor after reaching a maximum service 
pressure and switched on at repeated need of air. Switching 
pressure of 6 bar, max. pressure of 8 bar. 
 

V-belt 

 
Check the tension of the regular V-belt.  
 
Should it be necessary to tighten the fan belt, proceed as follows:  
• 

Remove the 4 screws of the motor.  

• 

Tighten the fan belt by pressing away from the motor unit.  

• 

Is the fan belt eager to have the screws of the motor re-

 attached. 

• 

Be sure the two pulleys to escape each other. 

Air filter 

 
Sometimes it is necessary to clean the air filter insertion. To do that, 
take the wing-nut out of the air filter cover and remove the foam 
filter. The filter can be cleaned with warm soap suds. Dry and 
reinsert the foam filter. Fix the air filter cover again.

37