background image

 

 

 

After removing the package, check whether the 

appliance and all parts are in a perfect condition. 

 

 

Protective glasses and ear protectors to be used 

at all times 

Protective glasses or appropriate eye and ear 

protection to be used at all times. Never aim with the 

compressed air stream at your body or other 

persons or animals. The air stream may accelerate 

undesirable items and they may get dangerously 

shot off. 

 

 

Protective equipment against electric shock to 

be used at all times

 

Never use the compressors near water or in wet 

conditions. 

 

 

Unintentional appliance starting 

Do not transport the compressor if plugged or if the 

air jet is pressurised. Before plugging the 

compressor, make sure the pressure sensor switch 

is in the OFF position. 

 

 

Proper storage of the compressor 

When the compressor is not being used, keep it 

unplugged in a dry place protected against climatic 

influences. Keep out of reach of children. 

 

 

Working clothing 

Do not wear loose clothing and jewels as they could 

get entangled in the components. 

 

 

Thorough servicing of the compressor 

Check the feeder cable at regular intervals. If 

damaged, have it repaired or replaced in the 

customer service centre. Make sure the outside of 

the compressor does not show any visible damage. 

Or contact the nearest customer service centre. 

 

 

Outdoor use 

If the compressor is used outdoors, extension cables 

designed to be used outdoors with appropriate 

marking may only be used. 

Caution: It is 

necessary to use a sufficient cable cross section 

(at least 1.5

 

mm

2

); with cables exceeding 10 m 

there may be problems at adverse temperatures 

when starting the appliance.

 

 

 

Attention 

Work cautiously and use common sense. Do not use 

the compressor when you are tired. The compressor 

must not be used when you are under the influence 

of alcohol, drugs or pharmaceuticals that may evoke 

tiredness. 

 

 

Check whether any components are not 

defective or untight 

If any protective equipment or other compressor 

components have been damaged, the appliance 

must be checked and you must make sure the 

operation will be safe before putting it into operation 

again.  

Any damaged parts must be repaired or replaced by 

a customer service centre or replaced based on 

instructions mentioned in the maintenance manual. 

 

 

Proper using of the compressor 

When operating the compressor, follow all 

instructions included in this manual. Do not let 

children or persons not familiarised with the way it 

works use the compressor. 

 

 

Keep the cowl screen clean 

Keep the engine cowl screen clean. Clean it 

regularly if the compressor is used in very dirty 

conditions. 

 

 

Compressor to be used under rated voltage 

Compressor to be used under voltage specified on the label 

with electric details. If the compressor is operated at voltage 

that is higher than the nominal value, the engine may get 

overheated. 

 

 

Do not use the compressor if defective 

If the compressor makes abnormal sound or is vibrating 

intensively or seems to be defective in any other way when 

being operated, it must be immediately stopped; have the 

cause identified in the nearest customer service centre. 

 

 

Plastic parts not to be cleaned with solvents

 

Solvents like petrol, thinners, diesel or other alcohol-

containing substances may damage the plastic parts of the 

compressor; therefore, do not clean the plastic parts with 

such substances but use lye soap or suitable liquids instead. 

 

 

Original spare parts to be used only 

Claims arising from the warranty will not apply if spare parts 

of other manufacturers are used.  

Using different spare parts may lead to compressor 

malfunction. Original spare parts may be obtained through 

our authorised dealers. 

 

 

Do not make any change to the compressor 

Do not make any change to the compressor. Contact the 

customer service centre for any repair. Any unauthorised 

change may have a negative influence on the compressor 

performance; however, it may also cause serious injuries if 

made by a person not having the necessary technical 

knowledge. 

 

 

Do not touch the hot parts of the compressor 

Do not touch the pipes, engine and other hot parts of the 

compressor as there would be a risk of burn. 

 

Safety and protective equipment must be refitted properly 

after being serviced or repaired. 

 

It is absolutely necessary to know the accident prevention 

regulations applicable in the place of use and other generally 

recognised safety regulations. 

 

Before using the appliance, it is necessary to check the 

safety equipment. Make sure the visibly slightly damaged 

parts are able to work properly. 

 

Unless otherwise provided in these Operating Instructions, 

any damaged parts and safety equipment must be repaired 

or replaced by an authorised service centre. 

 

Have any damaged switches replaced in an authorised 

service centre. 

 

This appliance meets all applicable safety provisions. 

Repairs may only be executed by qualified electricians in 

authorised service centres, using original spare parts. Risk 

of accidents if not adhered to. 

 

Behaviour in case of emergency 

 

Provide necessary first aid treatment corresponding to the injury 

nature and seek qualified medical help as soon as possible. 

Protect the injured person from other injuries and calm him/her 

down. 

 

First aid kit must always be available in the place of your 

work in case of accident in accordance with DIN 13164. 

Material taken out of the first aid kit needs to be 

supplemented right away. 

If help is needed, please provide the following details: 

 

1.  Place of accident 

2.  Accident nature 

3.  Number of injured persons 

4.  Injury type  

 

Use as designated 

 

Piston compressor for compressed air production and filling for 

simple housework with compressed air. 

 

12

Summary of Contents for 225/08/24





























































Reviews: