22
Caution! Never switch the compressor on or off using
the plug. Pressure switch to be pressed at all times.
Do not leave the compressor on over night as it could
become a source of danger.
At the end of your working day, switch the appliance
off, release the air jet and unplug the compressor.
Warning: if the water that condenses is not drained,
it may corrode the receiver, reducing its capacity and
impairing safety.
Never leave the appliance exposed to adverse wea-
ther conditions (rain, sun, fog, snow).
If this compressor is used outdoors, always remember
to stow it after use in a covered or closed place.
Never use the compressor outdoors in rain or bad
weather.
Do not place flammable or nylon/fabric objects close
to and/or on the compressor.
Do not cover the air inlets on the compressor.
The compressor must not be fitted in a vehicle for in-
dustrial purposes without an inspection by an expert!
If the compressor is used for industrial purposes, it
must be checked by an expert before putting into
operation for the first time. Such check must be
ordered by the operator (under BetrSichV Section 17
No. 25 – operation safety regulation)
Caution! When fitted in automatic equipment, it is
necessary to install appropriate alarm or warning
devices in case of power outage or malfunction or
compressor (e.g. feed line, etc.) failure.
Operation at lower temperatures
At lower temperatures, below 5°C, problems may
be experienced when starting. They are manifested
by growling of the electric motor. In such a case, the
appliance must be immediately switched off and oil
(5W30) changed in warmer conditions.
To guarantee perfect and reliable operation of the
rotary and percussive pneumatic tools such as impact
wrenches, staplers or nailers, etc., the compressed air
must be supplied filtered - with oil via the lubricator
or maintenance unit
A filtered water separator should be used for var-
nishing in any case.
To select a suitable pneumatic tool, the tool air
consumption and the compressor effective amount
delivered must necessarily be considered.
(Pneumatic tools and accessory equipment can be
Never yank the power cable to disconnect the plug
from the power outlet or to move the compressor.
Warning: the compressor may restart when power is
restored following a blackout.
Compressed air is a potentially dangerous
form of energy; always take great care when
using the compressor and its accessories.
This device is not intended for use by persons (inclu-
ding children) with limited physical, sensory or mental
capabilities or without the necessary lack experience
or knowledge unless they are supervised by a person
who is responsible for their safety or were instructed
by that person in how to use the device.
Children should be supervised to ensure that they do
not play with the device. Always keep children and
unauthorised persons out of reach of the appliance.
Never use the compressor without being supervised.
Never direct the jet of air towards persons, animals or
your body.
Never keep the air flow in body holes as that could
lead to fatal injuries!
Keep the work area free.
When operating, the compressor must be placed on a
stable surface.
The compressor must be used in a vertical position
only.
Caution! The compressor may only be used with
appropriate wheels and rubber bumps.
Safety goggles should be worn when using the
compressor in order to protect the eyes against any
foreign bodies lifted by the jet of air.
If possible, when using air-powered accessories, wear
safety clothing.
Always maintain a safety distance of at least 4 meters
between the compressor and the work area.
Caution! The pneumatic hose may lash you when the
quick-acting coupling is opened! The pneumatic hose
should be held by hand.
Always use the handle to move the compressor.
When using compressed air, you must know and
comply with the safety precautions to be adopted for
each type of application (inflation, airpowered tools,
painting, washing with water-based detergents only,
clinching, etc.).
When using compressed air, you must know and
comply with the safety precautions to be adopted for
each type of application (inflation, airpowered tools,
painting, washing with water-based detergents only,
clinching, etc.).
EN
ENGLISH
