background image

730372.doc 3429 

8

If the spotlight moves properly but does not light, 

examine the halogen bulb.  Replace 

it if it appears discolored or broken.  If the bulb appears normal, test for a faulty relay by listening 
at the base of the light while someone else activates the bulb using the control panel.  If no "click" 

is audible, or if a "chattering" sound is not heard, replace the Relay PC board.  NOTE: Low voltage 
or a faulty circuit board may cause similar symptoms. 

If the spotlight will not move left 

or

 right

 

but operates normally otherwise, listen at the 

base of the light while someone else presses the left or right directional buttons.  If the lower motor 
makes no sound when it is activated, replace the lower motor.

 

If the spotlight does 

not 

move in one direction 

only

 (up, but not down or left, but not 

right), and the wiring has been checked, replace the control panel. 

 

If your light has a problem that is not described above, contact the GUEST Co. Service Department 

for assistance.  

 

 
 

LIMITED WARRANTY 

For one (1) year from the date of original purchase, The Guest Co. will, at its discretion, repair 

or replace for the original consumer, free of charge, any parts found defective in material or 

workmanship.  All transportation charges under this warranty must be borne by the consumer.  
 

Proof of purchase is required: A computerized register receipt is required. Hand-written 
receipts are not accepted for warranty proof of purchase.  In the absence of a receipt, warranty 

period will be calculated from date of manufacture printed or stamped on the product. 
 

There is no other expressed warranty. Implied warranties, including those of merchantability 

and fitness for a particular purpose, are limited to one year from the date of purchase. This is 
the exclusive remedy and consequential damages are excluded where permitted by law. 

  

 

Tel:  (707) 226-9600  

 

 

 

 

Email: 

info@marinco.com

 

Fax: (707) 226-9670   

 

 

 

 

Website: 

www.marinco.com

 

  

730372 REV B 

             

 

 

 

Summary of Contents for 503A BEAMER









Reviews: