background image

18

 

 

AR004525

Four-channel thermometer 
for external probes

This  model  can  measure  up  to  four  temperature 

values transmitted by Pt1000/E series external probes. 
The response  to  a  temperature  jump  depends 
on the connected  probe  design.  As  a  rule,  this  model 
is few times faster than that using the inner sensor. It is 
often used to  monitor locations where the device itself 
is not directly in the measuring space and only probes 
are in. The maximum length of each probe lead should 
not  exceed  15  m.  It  is  recommended  to  use  shielded 
cables.  To  maintain  the  IP  rating,  the  unused  probe 
connectors  should be provided with a  supplied closing 
cap.  

AR006088

Compact thermometer - 
hygrometer

This  model  is  designed  to  measure  temperature, 

relative humidity and dew-point temperature by internal 
sensor,  no  additional  probes  or  sensors  can  be 
connected. It is characterized by a simple and compact 
design and a relatively long response to a temperature 
and  humidity  jump,  compare  to  model  with  external 
probes.  The  sensors  are  located  under  the  grid 
on the front of the unit and are protected with Teflon foil. 
Foil  permits  water  vapour  but  prevents  water  from 
permeating  the  liquid  state.  The  device  is  suitable 
for measuring in places where there is no rapid change 
in  temperature  or  relative  humidity,  and  there  is 
no condensation  of  water  vapours.  If  water  vapour 
condensation 

occurs 

inside 

the 

datalogger, 

then the resulting  water  will  remain  there  and  may 
damage  its  electronics.  The  device  is  placed  directly 

in the  measured  space,  while  the  installation  needs  to 
ensure sufficient level of GSM signal at the installation 
location. As the internal battery creates a parasitic heat 
during the charging period, the measurement accuracy 

may be affected by up to 1 º C.

  The calibration of this 

instrument  in  the  laboratory  is  recommended  with  the 
open bottom part of the battery box, to allow airflow from 

Summary of Contents for AR003954







































































Reviews: