background image

Supplied By www.heating spares.co  Tel. 0161 620 6677

Page 2

1.  Handling and Storing the Appliance
This appliance should be handled carefully to avoid damage and the recommended 
method is shown opposite. A team lift - When lifting the unit:-
•  Work with someone of similar build and height if possible.
•  Choose one person to call the signal
•  Lift from the hips at the same time, and then raise the unit to the desired level.
•  Move smoothly in unison. 

The appliance is supplied shrink wrapped on a timber installation base. Carrying 
handles are provided towards the top of the left hand side of the casing and at the 
bottom of the opposite side.

If the unit needs to be stored prior to installation it should be stored upright in a dry 
environment and on a level base/floor.

Note:  Although  the  above  guidance  is  provided  any  manual  handling/lifting 
operations  will  need  to  comply  with  the  requirements  of  the  Manual  Handling 
Operations Regulations issued by the H.S.E. 

The appliance can be moved using a sack truck on the left hand face although care 
should be taken and the route should be even. In apartment buildings containing a 
number of storeys we would recommend that the appliances are moved vertically 
in a mechanical lift. If it is proposed to use a crane expert advice should be obtained 
regarding the need for slings, lifting beams etc.
 

TM

benchmark

The code of practice for the installation,

commissioning & servicing of central heating systems

2.  System Installation 
Any installation must be in accordance with the relevant requirements of the current 
issue of Gas Safety (Installation and Use) Regulations, Local Building Regulations, Local 
Water Company Bylaws and Health & Safety Document No. 635 – The Electricity at 
Work Regulations 1989. The detailed recommendations are contained in the current 
issue of the following British Standards and Codes of Practices: -

BS 5440 Pts. 1 & 2; BS 5449; BS 5546; BS 7074 Part 1; BS 6700; BS 6798; BS 6891, BS 
7593, IGE/UP/7/1998

3.  Gas Consumer Council
The Gas Consumer Council (GCC) is an independent organisation which protects 
the interest of all gas users. If you need advice, you will find the telephone number 
in your local telephone directory under Gas.

4.  Equipment selection
This  information  is  provided  to  assist  generally  in  the  selection  of  equipment. 
Responsibility  for  selection  and  specification  of  our  equipment  must,  however, 
remain that of our customers and any expert or consultants concerned with the 
installation(s). Therefore please note that: -

a)  We do not therefore accept any responsibility for matters of design selection or 
specification for the effectiveness of an installation containing one of our products.
b)   All goods are sold subject to our Conditions of Sale which are set out in the 
Appendix to this document.

4.   Warnings
a)  
The GulfStream

A-Class

 is for use on Natural Gas only and must not be used on any 

other gas.
b)  This appliance must be serviced and installed by a competent person e.g. CORGI 
Registered installer. All CORGI registered installers carry a CORGI ID Card and have a 
registration number. You can call CORGI direct on 01256 372300.
c)  As part of the industry wide ‘Benchmark’ initiative all GulfStream

A-CLASS 

appliances 

now include a Benchmark Installation, Commissioning and Service Record Logbook. 
Please read this carefully and complete all sections relevant to this appliance. Failure 
to do so may affect warranty.
d)  If sealed components in the appliance are replaced and/or re-commissioned 
in the field then these must be done strictly in accordance with manufacturer’s 
instructions and these components must be re-sealed
.

IMPORTANT NOTICES

5.  Continuous Improvements
In the interest of continuously improving the 
GulfStream

A-CLASS 

range, Gledhill Water Storage 

Ltd  reserves  the  right  to  modify  the  product 
without notice and in these circumstances this 
booklet which is accurate at the time of printing 
should be disregarded.

Issue 1: 03-05

Summary of Contents for GS A-Class 12/OV













































Reviews: