background image

IMPORTANT SAFETY NOTICE 

 

This play ground equipment is built for optimum safety.  However, certain precautions apply 
whenever you operate a piece of play ground equipment.  Be sure to read the entire manual 
before you assemble or operate your equipment.  In particular, note the following safety 
precautions to reduce the likelihood of serious or fatal injury. 

 

1.  Children must be supervised at all times and never left unattended with the unit.  
2.  Do not install the equipment over concrete, asphalt, packed earth, grass, carpet or any other 

hard surface.  A fall onto a hard surface can result in serious injury to the user. 

3.  Make sure the surfaces, either indoors or outdoors, are free of objects that may cause tipping 

over. 

4.  Place the equipment on level ground (to avoid possible tipping, and the possibility of the loose-

fill material washing away during heavy rains), not less than 6 ft (1.8 m) from any structure or 
obstruction such as fence, garage, house, overhanging branches, laundry lines, or electrical 
wires. 

5.  Make sure bystanders are at least 5 feet away from the equipment while it is in motion. No one 

should be allowed to walk close to, in front of, behind, or between moving items.  

6.  Keeps hands and feet away from the pivot area. 
7.  Do not get off from seat while it is in motion. 
8.  Do not stand on the teeter-totter.  This could cause damage to the ride and result in injury. 
9.  Do not swing with empty seat. 
10. Children should not wear loose clothing. Attire should include well-fitting shoes. 
11. 

This teeter totter is intended for use by children from ages 3 to 13

12. 

Maximum weight capacity 400 lbs.

 

13. Only two persons should be using the equipment at the same time. 
14. Impact-absorbing material must be placed around the teeter totter.  Please refer to the 

PLAYGROUND SURFACING MATERIALS in page 4. 

15. Maximum fall height: 52 inches. 
16. To prevent serious injury, children must NOT use the equipment until properly installed. 
17. To prevent serious injury, parents must make warnings to children not to use this equipment in 

a manner other than intended. 

18. To prevent serious injury, parents must make warnings to children not to attach items to the 

equipment that are not specifically designed for use with the equipment. 

19. Children should remove their bike or other sports helmet before using this equipment. 
20. 

Lock the teeter-totter when not in use with the provided locking mechanism by clipping 
the washer from the cable strap to the carabineer clip.

 

21. 

Do not remove the carabineer clip.

 

22. 

Insert the L-shape locking pin into the washer on the cable strap to prevent 
unauthorized access when the teeter totter is in use.. 

 

23. 

This teeter totter is designed for

 

HOME USE ONLY

 

Assembled dimension: 112” x 35” x 36” (L x W x H) 

 

 

SAVE THESE INSTRUCTIONS. 

 
 
 
 
 
 
 
 

Summary of Contents for TEETER TOTTER TT-320
















Reviews: