GYMFORM SLIM FOLD TREADMILL, Instruction Manual

8

emergency key to the clothing you are wearing.
When the emergency key (2) is attached to the 

control panel (1), the screen will light up and 

you will hear five beeps.
5. Press the   button (11) to start the treadmill 

belt. The device will not start working for three 

seconds, as displayed on the screen. The 

device will beep so you can get ready to use it. 

After three seconds, the belt will start moving, 

the device will go into manual mode and the 

speed will be displayed on the screen.

The initial speed is 1 km/h.

6. Press the ↑ button (13) to increase the speed 

by intervals of 0.1 km/h each time you press the 

button. The maximum speed is 6 km/h.

7. Press the ↓ button (12) to reduce the speed.

8. Press the MODE button ( 10) to view the 

other  function  options  on  the  screen.  Each 

time you press the button, a different function 

will be displayed: the SPEED, the TIME, the 

distance (DIST), the kilocalories burned (CAL) 

and heartbeat (PULSE). When the indicator 

displays  the  SCAN  function,  the  information 

(speed, time, distance and calories) will be 

displayed  on  the  screen  every  five  seconds 

without the need to press any buttons.

9. To find out your heart rate, select the PULSE 

option on the control panel and place your 

hands on each of the pulse sensors (28) and 

press down until the heartbeat is displayed on 

the screen.

10. Each  function  indicator  (14)  will  light  up 

when the function is selected.
Note: Each time you use a programme, your 

data on distance, time and calories are saved. 

To set the panel to zero, press the MODE 

button (10) for two seconds once the belt has 

stopped.  
11.  The treadmill has a manual mode (P0) and 

three automatic programmes:
P0 - Manual mode

P1 - Intervals

P2 - Resistance

P3 - Cardio Booster 
To change programmes, first set the panel to 

zero. When the panel is set to zero, press the 

MODE  button  (10)  after  choosing  the  pulse 

function  (PULSE)  and  the  panel  will  flash  on 

the programme you are working on (P0, P1, P2 

o P3). Use the ↓ button (12) and the ↑ button 

(13) to choose the desired programme.

Even  if  you  use  the  automatic  programmes, 

the speed can be adjusted by increasing or 

reducing it to fit your needs. When the speed 

is automatically changed on a programme, it is 

increased or reduced proportionately. 

In programme P1, the programmed speed can 

be increased or reduced by 1.0 km/h.

The speed of programme 2 can be reduced to 

1.0 km/h, but cannot be increased.

The speed of programme P3 can be  reduced 

to 2.0 km/h, but cannot be increased.

Each time the programme speed is changed, 

you will hear three warning beeps so you are 

ready.
12. When you have chosen the programme 

you want to use, you can select the workout 

time before you begin. Go to the TIME function, 

which  will  be  set  at  the  default  time  of  30 

minutes. The time can be reduced by pressing 

the ↓ button (12) or increased by pressing the ↑ 

button (13). The times available are 30, 20 and 

10 minutes.

13.  When the treadmill is operating and the   
button 

 (11) is pressed, the treadmill will 

slow down and eventually stop. To restart the 

treadmill, press the button again and all the 

functions  will  the  same  as  in  the  previous 

workout.

14. Press  the  MODE  button  (10)  for  three 

seconds to erase all the previous functions and 

start a new workout.

15. If you want to stop the treadmill quickly, pull 

on the emergency key.

Unfolding the device (see Picture 3)

1. Remove the two handlebar screws (26). 

2. Lower the handlebars (6) to the horizontal 

position.

3. Hold onto the base (3) with one hand and use 

the other to remove the screw on the vertical 

bar (5) and unlock the base.

4. Slowly lower the base (3) until it is on the 

floor.

5. Firmly tighten the lock screw (7).

Device folding system (see Picture 4)

1. Loosen the lock screw (7).

2. Raise the base to the vertical position and 

hold it in place.

3. Attach the base (3) to the vertical bars (17) 

using the screw on the vertical bar (5).

4. Remove the two handlebar screws (26). 

5. Raise the handlebars (6) to the vertical 

position. Replace the two handlebar screws 

(26) so they are not lost.

6. When  the  device  is  folded,  it  can  be 

transported using the wheels (30).

Product Cleaning and Maintenance

•  Before performing daily cleaning, make sure 

the device is off by pressing the ON/OFF button 

and pulling the plug from the power supply. 

•  Do not use abrasive products or solvents to 

clean the device.

•  Remove any dirt from the device with a damp 

cloth. 

•  Use a dry cloth to clean the plug and control 

panel. Do not use a damp cloth.

•  Do not use the device in very damp or dusty 

places that could cause the device to fail. Set 

up the device on a flat surface to prevent it from 

falling and breaking down.

•  Do not use the device for more than an hour. 

Rest for an hour after each one-hour workout. 

The components should be kept clean. Both 

sides of the belt should be cleaned to reduce 

dirt  build-up.  Before  using  the  device,  make 

sure the treadmill surface is clean. Use soap 

and a damp cloth to clean the belt. Do not use 

solvents. Wipe off the sweat on the handlebars 

after each use.