GYS LUXMAIN QUICK LIFT L520E Operating And Control Manual Download

Page: 16 / 18

Condition of the load-bearing construction (mechanical

structure)

Status of the locking blocks (height 1 and height 2)

Status of locking bars, cams and pins

Condition of the jacks (leaks, rust...)

Condition of the rubber chocks (and 4x4 option)

Condition of the power cord of the hydraulic power pack

General condition of the hydraulic power pack

Functional test of the lifting platform with vehicle

Control result

Commissioning is not allowed

No anomalies: commissioning granted

Safety check carried out on:

............................................................................................................................

Name and address of the authorised person:

..............................................................................................................

Signature of the authorised person

MAINTENANCE LOG

.............................................................................................................................................................................

Summary of Contents for LUXMAIN QUICK LIFT L520E



















Search results

Summary of Contents for LUXMAIN QUICK LIFT L520E

Reviews:

Related manuals for LUXMAIN QUICK LIFT L520E

Brands by name

Popular brands

GYS LUXMAIN QUICK LIFT L520E, Operating And Control Manual

Search results

Summary of Contents for LUXMAIN QUICK LIFT L520E

Reviews:

Related manuals for LUXMAIN QUICK LIFT L520E

Brands by name

Popular brands