64
Manuale d’utilizzo
WF 35
Traduzione delle istruzioni
originali
Quando si utilizza la guaina rossa o blu (saldatura alluminio), si raccomanda di utilizzare l’accessorio 90950 (I-C).
Questa guida per guaina inox migliora il centraggio della guaina e facilita il flusso del filo.
Video
SALDATURA SEMI-AUTOMATICA IN CUSI E CUAL (MODALITÀ BRASATURA)
Il materiale può saldare il filo CuSi e CuAl di da Ø 0.8 e 1.0 mm.
Allo stesso modo dell’acciaio, il tubo capillare deve essere messo in posizione e bisogna utilizzare una torcia con una guaina in acciaio. Nel caso della
brasatura, bisogna utilizzare dell’argon puro (Ar).
SALDATURA SEMIAUTOMATICA FILO ANIMATO
L’apparecchiatura può saldare fili animati da Ø 0,9 a 1,6 mm. I rulli originali devono essere sostituiti con rulli specifici a filo animato (opzionali).
Saldare filo animato con un ugello standard potrebbe portare al surriscaldamento e deterioramento della torcia. Rimuovere l’ugello originale della
vostra torcia MIG-MAG.
COMBINAZIONI CONSIGLIATE
(mm)
Corrente (A)
Ø Filo (mm)
Ø Ugello (mm)
Flusso (L/min)
MIG
0.8-2
20-100
0.8
12
10-12
2-4
100-200
1.0
12-15
12-15
4-8
200-300
1.0/1.2
15-16
15-18
8-15
300-500
1.2/1.6
16
18-25
MAG
0.6-1.5
15-80
0.6
12
8-10
1.5-3
80-150
0.8
12-15
10-12
3-8
150-300
1.0/1.2
15-16
12-15
8-20
300-500
1.2/1.6
16
15-18
MODALITA’ DI SALDATURA MIG / MAG (GMAW/FCAW)
Processi di saldatura
Parametri
Regolazioni
Manuale
Sinergico
Coppia
materiale/gas
- Fe Ar 15% CO
2
- ...
-
Scelta del materiale da saldare.
Parametri di saldatura sinergica
Diametro del fino
Ø 0.6 > Ø 1.6 mm
-
Scelta del diametro del filo
Comportamento
pulsante
2T, 4T
Scelta della modalità di gestione della saldatura a pulsante.
Modalità di punte
-
ggio
Spot, Spot-Délai
Scelta della modalità di puntatura
1° Regolazione
Spessore
Corrente
Velocità
-
Scelta di regolazione principale da visualizzare (Spessore del pezzo da
saldare, corrente media di saldatura o velocità del filo).
L’accesso a certi parametri di saldatura dipende dalla modalità di visualizzazione selezionata : Parametri/ Modalità di visualizzazione : Easy o Ex
-
pert. Fare riferimento al manuale dell’IHM.
PROCESSI DI SALDATURA
Per avere maggiori informazioni sulle sinergie GYS e i processi di saldatura, scannerizzare il QR code:
MODALITÀ DI PUNTATURA
• Spot
Questa modalità di saldatura permette di pre-assemblare i pezzaprima della saldatura. La puntatura può essere manuale attraverso il pulsante o
cronometrato con un tempo di puntamento predefinito. Questo tempo di puntatura permette una migliore riproducibilità e la realizzazione di punti non
ossidati.