27
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
INSTALLATION AND SERVICE MANUAL
INSTALLATION AND SERVICE MANUAL
INSTALLATION AND SERVICE MANUAL
INSTALLATION AND SERVICE MANUAL
INSTALLATION AND SERVICE MANUAL 917N-CMT, 927CMT, 957CMT
184617-02
9.2 MTS Motor Replacement – continued
NOTE
: If the hole in motor bracket and the
hole in the electrical box bracket do not line
up, loosen nuts on the 2 bolts that secure
the 4" x 4" (10 cm x 10 cm) electrical box to
the frame, tighten nuts on bolts when holes
align. (If the holes still do not line up it may
be necessary to enlarge the holes on the
motor support bracket so the bolt will go
through without binding.)
12. Remove the alignment bushing and
install the wavy spring washer.
13. Install the MTS on the cabinet wall by
aligning the coupling and the motor
shaft.
14. Turn the roller assembly while pushing
the MTS back until completely en-
gaged.
15. Install the two mounting screws. Be
sure the base is flush against the back
wall before tightening screws.
16. Install the MTS hose assembly accord-
ing the Operator’s Manual.
Important
Use original Duke hose only. The
freezer will not operate properly with
any other type of hose. Never twist the
hose when assembling or installing.
Important
The MTS will not operate unless the
handle is in the closed and locked
position.
CAUTION
Mix Transfer System will be
pressurized during
operation. Make sure all
components and fasteners
are secure before start-up.
17. Place a container of water in the
cabinet and insert pickup tube in
bucket. Place an empty bucket under
the dispense head.
18. Reconnect the main power supply.
Place the MTS switch in the "ON"
position and allow MTS to fill and
pressurize the cylinder. Open the
spigot and allow some water to drain.
19. Repeat so that the MTS runs for at
least two minutes.
20. Place MTS switch in the “OFF”
position and drain the water from the
cylinder. Remove the duckbill valve
and allow water to drain from the mix
pickup tube.
21. Unlock the MTS handle and pull down
to gain access to the hose/roller
cavity. Check to make sure the MTS
hose has not moved to the back side
of the rollers. If hose has moved to the
back side of the roller cavity, contact
the factory.