background image

Views 

Layer 2 Ethernet interface view, Layer 2 aggregate interface view, Layer 3 Ethernet interface view, Layer 

3 aggregate interface view 

Predefined user roles 

network-admin 
mdc-admin 

Examples 

# Enable OAP on interface Ten-GigabitEthernet 2/16/0/1. 

<Sysname> system-view 

[Sysname] interface Ten-GigabitEthernet2/16/0/1 

[Sysname-Ten-GigabitEthernet2/16/0/1]oap enable 

oap timer clock-sync 

Use 

oap timer clock-sync

 to set the clock synchronization timer. 

Use 

undo oap timer clock-sync

 to restore the default. 

Syntax 

oap timer clock-sync

 

minutes

 

undo oap timer clock-sync 

Default 

The clock synchronization timer is set to 5 minutes. 

Views 

System view 

Predefined user roles 

network-admin 
mdc-admin 

Parameters 

minutes

Specifies the clock synchronization timer value in minutes, in the range of 0 to 1440. Setting this 

argument to 0 disables clock synchronization. 

Usage guidelines 

The clock synchronization timer regularly triggers the OAP manager to send clock and time zone 
synchronization notifications to OAP clients. These notifications keep the clients' clocks synchronized to 

the manager's clock. 

Examples 

# Set the clock synchronization timer to 20 minutes. 

<Sysname> system-view 

[Sysname] oap timer clock-sync 20 

Summary of Contents for S12500 Series

















Reviews: