background image

 

10-14 

undo ip unreachables

 

View 

System view 

Default Level 

2: System level 

Parameters 

None 

Description 

Use the 

ip unreachables enable

 command to enable the sending of ICMP destination unreachable 

packets.  

Use the 

undo ip unreachables

 command to disable sending ICMP destination unreachable packets. 

Sending ICMP destination unreachable packets is disabled by default. 

Examples 

# Enable sending ICMP destination unreachable packets. 

<Sysname> system-view 

[Sysname] ip unreachables enable 

reset ip statistics 

Syntax 

reset ip statistics 

View 

User view 

Default Level 

2: System level 

Parameters 

None 

Description 

Use the 

reset ip statistics

 command to clear statistics of IP packets. 

Related commands: 

display ip interface 

(

IP Addressing 

in the 

Layer 3 – IP Services Command 

Reference

); 

display ip statistics 

(

IP Performance Optimization

 in the 

Layer 3 – IP Services Command 

Reference

). 

Examples 

# Clear statistics of IP packets. 

<Sysname> reset ip statistics 

reset tcp statistics 

Syntax 

reset

 

tcp

 

statistics 

Summary of Contents for WA2600 Series




































































































































Reviews: