background image

 

12-3 

<Sysname> display ipv6 fibcache 

FIB Cache: 

 Total number of Routes : 0 

display ipv6 interface 

Syntax 

display ipv6 interface

 [ 

interface-type 

interface-number

 ] ] [ 

verbose

 ] 

View 

Any view 

Default Level 

1: Monitor level 

Parameters 

interface-type

: Interface type.

 

interface-number

: Interface number. 

verbose

: Displays detailed IPv6 information of an interface. 

Description 

Use the 

display ipv6 interface

 command to display the IPv6 information of an interface for which an 

IPv6 address can be configured. 

If 

interface-type interface-number

 is not specified, the IPv6 information of all interfaces for which IPv6 

addresses can be configured is displayed; if only 

interface-type

 is specified, the IPv6 information of the 

interfaces of the specified type for which IPv6 addresses can be configured is displayed; if the 

interface-type interface-number

 is specified, the IPv6 information of the specified interface is displayed. 

Examples 

# Display the IPv6 information of VLAN-interface 2. 

<Sysname> display ipv6 interface vlan-interface 2 verbose 

Vlan-interface2 current state :UP 

Line protocol current state :UP 

IPv6 is enabled, link-local address is FE80::1234:56FF:FE65:4322 

  Global unicast address(es): 

    2001::1, subnet is 2001::/64 

10::1234:56FF:FE65:4322, subnet is 10::/64 [AUTOCFG] 

      [valid lifetime 4641s/preferred lifetime 4637s] 

  Joined group address(es): 

    FF02::1:FF00:1 

    FF02::1:FF65:4322 

    FF02::2 

    FF02::1 

  MTU is 1500 bytes 

  ND DAD is enabled, number of DAD attempts: 1 

  ND reachable time is 30000 milliseconds 

  ND retransmit interval is 1000 milliseconds 

  Hosts use stateless autoconfig for addresses 

IPv6 Packet statistics: 

 

 

InReceives: 

    0 

Summary of Contents for WA2600 Series




































































































































Reviews: